 | | Re: *** NQC ***
|
|
Hi is RCX command center the same thing as NQC? What I mean is , is NQC part of the RCXcc? Thanks -Mike -- Did you check the web site first?: (URL) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: *** NQC verus other programming environments ***
|
|
BMajik5127@aol.com wrote: [snip] (...) Hello ... RcxCC (RCX Command Center) is an NQC integrated development environment written by Professor Mark Overmars and placed into the public domain. RcxCC makes NQC development much easier if you are a (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Virtual PC and Mindstorms
|
|
You need to patch the Mindstorms software to get it to work. There are two patches that I know of. One is by Dave Hylands, and you can find it and instructions for using it at: (URL) be warned. It is very sloooow under VPC. I'm using it with a 266 (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Virtual PC and Mindstorms
|
|
Yes, it's awful cool that the robo-lab stuff from pitsco-dacta is available on-line now. Just a month or two ago it wasn't. I imagine they had quite an influx of folks ordering catalogs for non curricular interestsover the last year. Speaking of (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | What is RPM of Gear Motor???
|
|
I just made an optical shaft encoder with the light sensor and a spinning paper disc, and measured somewhere near 1300 RPM using datalogging on the RCX. Does anyone know if this is close to the technical specs of the gear motor that I was using to (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Light Sensor Lead Length
|
|
I picked up a second RIS a while back and was sorting the pieces tonight when I noticed that the lead to the new light sensor was longer then my older one. The older one is 4 inches and the new one is 6 inches long. I looked at both of them closer (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
oops. forgot to divide by 2. make that between 600 and 720 RPM. I called pitsco lego dacta and they report 350 RPM... i wonder if i'm doing something else wrong in my analysis... but i can't find it! anyone else? (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
I found only this post in a search of LUGNET Robotics for "RPM" (...) -- Did you check the web site first?: (URL) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
thanks. i found out that my time axis on my graph had numbers about half of what they should have been, so I got around 350 RPM too. yay. -Ben (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: *** NQC ***
|
|
NQC is actually two things: a language to program the RCX and a compiler for that language. (at first I distinguished between the language: NQC, and the compiler: nqcc, but this was even more confusing) RcxCC is a great front-end for NQC. It (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|