To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4701 (-10)
  Og Needs More Inputs
 
-So, I'm building an RCX-based robot that already has - and needs - a light sensor, a rotation sensor, and a touch sensor. I've discovered I can include another touch sensor on the same input as the light sensor. (Thanks to (URL) Can the same be (...) (28 years ago, 27-Apr-99, to lugnet.robotics)
 
  Re: serial-port problem.
 
(...) This error is thrown whenever the PC cannot communicate w/ the Tower, or when the Tower cannot communicate with the RCX. When you try to download the program into the RCX, does the little green LED in the Tower light up? If the green light is (...) (28 years ago, 27-Apr-99, to lugnet.robotics)
 
  serial-port problem.
 
Hi!! I'm Nohala. I like mindstorms very much. But a problem occured to me. That is... I want to use NQC in Linux box, and installed it. Then I tried to download a test program to RCX. But error emerged. % nqc -d test.rcx Downloading Program:error (...) (28 years ago, 27-Apr-99, to lugnet.robotics)
 
  Re: Reading sensors at equal intervals.
 
(...) IIRC, it preferentially executes a single instruction received from the IR connection, otherwise takes the next instruction from the next task and executes that instead. (...) Probably. I don't think LegOS supports (what I'd call) a software (...) (28 years ago, 26-Apr-99, to lugnet.robotics)
 
  Re: Reading sensors at equal intervals.
 
(...) <snip> (...) That looks like a "no" then... How does the timing of tasks work? I seem to recall reading somewhere that the firmware executes the tasks in sequence - is there any timing element to this, or does it just do task 1, then (...) (28 years ago, 26-Apr-99, to lugnet.robotics)
 
  Re: Pics of 1999 Mindstorms items
 
S. Crawshaw wrote in message ... (...) I offered an explanation for that in a previous post. May want to look it up. Eric Brok (28 years ago, 26-Apr-99, to lugnet.robotics)
 
  Re: pneumatic switch control
 
Dennis Clark wrote in message ... (...) dropped (...) See demonstartion of the principle: (URL) pneumatic control from menu Eric Brok Visit LEGO ON MY MIND: (URL) Control section: (URL) section: (URL) (28 years ago, 26-Apr-99, to lugnet.robotics)
 
  Re: Reading sensors at equal intervals.
 
(...) You are right, the timer values as seen by the firmware are in 1/10ths of a second. I lost myself in H8-land, which has a 1 ms timer that gets divided down before being seen by the firmware. -Kekoa (28 years ago, 25-Apr-99, to lugnet.robotics)
 
  Re: Reading sensors at equal intervals.
 
(...) I though that the four "Timer()" values read out in 100ms increments only. Is there a way to get a 1ms timer with NQC? thanks, DLC (28 years ago, 25-Apr-99, to lugnet.robotics)
 
  Re: Reading sensors at equal intervals.
 
(...) By standard firmware, I assume you mean using the byte codes ala NQC or something similar. If you only want semi-precise timing, you can use the wait opcode to delay for approximately 100 ms between sensor samples. If you want something more (...) (28 years ago, 25-Apr-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR