To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4341 (-10)
  Re: Polarity Switch = Pressure Switch
 
(...) 8462 comes with two of them, and is available from Lego S@H. I'd like to see reissues of the construction vehicles as well. alex -- Did you check the web site first?: (URL) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Re: Polarity Switch = Pressure Switch
 
(...) Heck, I'd love to try some pneumatics, but you can't get a storage tank anywhere these days can you? All of the cool Technic kits are discontinued, no subs, (and while I'm whining) no shuttles, no tracked vehicles, only Throwbots and (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
 
  Re: Polarity Switch = Pressure Switch
 
I have not tried pneumatics yet. I know where I will look when I try them out. This is another neat clean working device. Nice work! Bob Fay rfay@we.mediaone.net The Shop (URL) Hempel <rhempel@bmts.com> wrote in message (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
 
  multi-device output controller
 
I've been considering various ways to control more than three output devices with only the three ports and came up with the following idea. I don't have the electrical design knowledge to implement, so if this idea sounds good, I'd like to (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Re: 3-wire converter for homebrew sensors
 
(...) It is a heck of a lot of complexity for a little added linearity. If you look at the plots on my general purpose interface section; the simple resistor interface is pretty linear. I think most of the nonlinearity in the powered version is due (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Polarity Switch = Pressure Switch
 
Hi All, Just got my first Technic Polarity Switch and quickly put together a Pressure Switch for Pneumatics. Check out: (URL) and let me know what you think... Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
 
  Re: 3-wire converter for homebrew sensors
 
(...) [snip] (...) Ahh, but the stipulated purpose for Pete's sensor brick is that it gives a _linear_ response that isn't corrupted by the non-linear diode drop caused by currents that are often less than 2ma and perhaps not past the "knee" region (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Re: 3-wire converter for homebrew sensors
 
(...) I wonder if you have looked at the simple method for connecting sensors to a RCX on my web page? It really only takes 6 diodes and a capacitor to create a powered sensor interface. Add a opamp if you need gain. This work was originally (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Links on Mindstorms in Education
 
For those interested here is a list of links on Mindstorms in Education that I compiled from my bookmarks as a request. Links are in no special order and some sites (not links) are mentioned twice. I just checked the links, so they should all be (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Re: lego turn table/list seems to hve slowed down
 
because robkc said, (...) for my digital camera (for panoramic shots) but have been having a hard time trying to get a stable base that rotates smoothly on a single shaft. I had to reply with: I used the same turntable for my digital cambot... Got (...) (28 years ago, 25-Mar-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR