To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 3751 (+10)
  Re: Sensors
 
The best source I can think of is the old family VCR. It has MANY momentary switches and probably 5 or more LED's in the front panel. There are two infra-red photosensors and a two sided infra-red LED on a post in the tape drive area. Good Luck! :-> (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  Re: Robotics sub-groups
 
(...) I agree with your gut- go with one group at first. I suspect it will be a relatively quiet group anyway. Dave (28 years ago, 15-Feb-99, to lugnet.admin.general, lugnet.robotics)
 
  Re: RCX Assembler programing
 
Actually, you'll need a Hitachi H8 assembler. I think there is reasonable support for Hitachi H8 in the gnu assembler. Unfortunately I can't remember if the assembler is in its own distribution package, or part of binutils. Dave (...) reply to: (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  Re: Sensors
 
(...) I found a GREAT source for small switches is inside an old mouse (um, computer mouse, NOT the rodent). I took apart several different brands of mice, and while they had different ways to measure movement, they all used the same type of (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  Re: RCX Assembler programing
 
=>From: dbaum@spambgoneenteract.com (Dave Baum) =>... =>Actually, you'll need a Hitachi H8 assembler. I think there is reasonable =>support for Hitachi H8 in the gnu assembler. Unfortunately I can't =>remember if the assembler is in its own (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  Re: Test Please disregard
 
Russell Nelson wrote in message <19990214033619.2640...wr.com>... (...) it's a little late to ask them that.... m. (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  Re: RCX Assembler programing
 
Hi Stefan, the h8 toolsuite will suit you fine, the GNU assembler has good support for the h8. You can use legOS without any problem at all - just provide something called "main", and you're all set. Ciao, Markus. (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  LEGO UK supplementary catalogue
 
I've put scans from the LEGO UK supplementary catalogue at: (URL) address for ordering your own copy is also there. It may take until tomorrow for the page to be visible outside the Demon domain. If there is sufficiant demand I could put the (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  RE: Robotics sub-groups
 
(...) As the creator? of HFORTH, I would LOVE to have a gruop focused on it. As it stands I am up to my eyeballs in paying consulting work and my family, and barely have enough time to keep development going. Markus has done a great job on LegOS and (...) (28 years ago, 15-Feb-99, to lugnet.admin.general, lugnet.robotics)
 
  Re: LEGO UK supplementary catalogue
 
In article <199902151348.IAA206...gnet.com>, lego-robotics@crynwr.com had their 2d worth... (...) Er, Mozza, old bean, either these images were scanned at 10dpi or they are a bit broken. Regards, Dave Ryder. (28 years ago, 15-Feb-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR