 | | Light outputs on RCX
|
| Has anyone ran lights from the RCX outputs? I need something brighter than an LED, any ideas? Thanks, Bryan Bible --- __o --- __o Tandem Computers --- _ \<,_ --- _ \<,_ Austin Texas --- (*) / (*) --- (*) / (*) bryan.bible@compaq.com -- Did you check (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
| | |  | | Re: Light outputs on RCX
|
| (...) I took apart a laser pointer. I put the laser module into a mutilated brick. I added a diode, an LM-317, appropriate resistors and a .1uF capacitor to make a 3 volt power supply. The diode makes it so the laser is on for motor forward, off for (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
| | |  | | Re: Light outputs on RCX
|
| Paul Haas writes: > On Mon, 18 Jan 1999, Bible, Bryan wrote: > > > Has anyone ran lights from the RCX outputs? I need something brighter than > > an LED, any ideas? > > I took apart a laser pointer. I put the laser module into a mutilated > brick. I (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
| | |  | | Where is "R4" on Handy Board Extension Schematic?
|
| I have just finished building the extension board, and, while it appears to work all right, I can't seem to find resistor R4 on the schematic. The power transistor near the on/off switch is getting quite hot with the expansion board piggybacked on (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
| | |  | | Re: new Throwbots
|
| (...) I doubt that these joints will be of much use - they're way to rigid, and there is not a real good place to attach a motive link. (28 years ago, 18-Jan-99, to lugnet.robotics)
| | |  | | Re: Light outputs on RCX
|
| (...) I made several diffrent color (even flashing!) lights with the mini xmas lights. they are real bright if you set the output to 8 or they work at any level. I took the bulb out of the little plastic holder and soldered wires to the wires on the (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
| | |  | | Re: new Throwbots
|
| (...) I just bought 2 of the new throwbots, Granite and Electro. I am not very impressed. The best part about them is the colored gears. Only because I am tired of gray. ---...--- @¿@ (URL) ,-, Follow the adventures of Capt. Jack Napalm! One thing (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
| | |  | | Re: RCX 2.0 -- ideas.
|
| (...) As a first step, how about simple 2 *4 s with logic gates in them? one of the connectors below for power, one output below, and two inputs on top :) Jasper (28 years ago, 18-Jan-99, to lugnet.robotics)
| | |  | | Re: RCX 2.0 -- ideas.
|
| (...) Whereas I have lost it several times form turning the RCX off.. a real pain. Jasper (28 years ago, 18-Jan-99, to lugnet.robotics)
| | |  | | RE: RCX 2.0 -- ideas.
|
| (...) Actually I'd be happy with just some Lego resistors, a 2X1 plate with the two studs as contacts and a resistor between them :) 100% pure multiplexed touch sensors Oh well. -- Did you check the web site first?: (URL) (28 years ago, 18-Jan-99, to lugnet.robotics)
| |