To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 2756 (+10)
  Re: ng/ml gatewaying
 
Todd Lehman writes: > In each case, if the 'From' header were left unchanged, then the respective > servers at each end would bounce any messages from the people it didn't > recognize -- which is many in both cases -- and the lists on each side (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  RE: simple touch sensor construction
 
If you place the bolts on diagonally opposite corners within the 2 x 2 square, then the connector will work from any orientation: Currently, the web page shows x o o o x o o o But if you do o x o o x o o o (The x's represent the nuts, and the o's (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  RE: simple touch sensor construction
 
> I've been working on constructing a touch sensor from parts of old > devices. I discovered that the micro switches from a MS mouse and a > Logitech mouse are the exact width of the inside dimensions of a 2x Lego > brick. Here are the instructions (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: ng/ml gatewaying
 
(...) Seriously? Okie dokie then, this'll be a snap to fix. Happy day! I'll disable 'From'-header munging for the lugnet.robotics->lego-robotics gateway (leaving it in for now on the other ng/ml gateways). You'll still be able to see real-life names (...) (28 years ago, 14-Jan-99, to lugnet.robotics, lugnet.admin.general)
 
  Pen Mounting Ideas?
 
Greetings! I have completed my "LEG-A-SKETCH", which works great, except for the marker, I use a standard dry-erase marker so it comes of the legos if I mess up :) My problem is that the lines will skip and the marker wont stay straight up and down, (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: Synchro drive in Lego
 
(...) Hi, I'm new here, so if I'm missing something, sorry! Seems what you are describing is just what I'd call a "relay switch". The output signal from the RCX goes to a switch, which switches the external power going to your motors. Seems to me (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: Synchro drive in Lego
 
(...) Hrm... how would you manage that? I cannot think of any purely mechanical approach that could do the trick. (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: Pen Mounting Ideas?
 
(...) If you construct a beam with an L-shaped cross section, the pen can rest along the groove in the corner of the L, held with small rubber bands at top and bottom. (...) Try putting the tires on the end of a hinged beam, so that they can provide (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: RCX 2.0 -- ideas.
 
(...) Brett, I have been working on a couple different transmission designs with multiple gear ratios. I am most interested in knowing how you used a RCX motor to shift the motors into the two different drive trains. Does it require any sensors? Any (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: simple but functional radar
 
(...) Chris, I built a little RadarBot just like yours (very minimalist, I love it :) and wrote some NQC code to drive it around my kitchen floor. It really zooms, until the left wheel inevitably falls off. :) The program below might help you get (...) (28 years ago, 14-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR