To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 24999 (-10)
  Re: Where should the 100 NXT testers' findings be shown?
 
(...) I didn't know it existed. Sorry! :) (21 years ago, 9-Jan-06, to lugnet.robotics, FTX)
 
  Re: mindstorms NXT and memory
 
(...) Since I'm an engineer, I will give you the standard engineering answer: Depends on the requirements! :-) (...) (URL) ARM architecture has been around for years and has been a very effective RISC based embeddded CPU core. That Wiki article does (...) (21 years ago, 9-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT and memory
 
(...) I'm curious - I'm a physicist, not by any means a hardware type. What *is* a standard amount of on-board FLASH for a embedded system? The NXT uses some sort of ARM processor (what the heck does that stand for anyway?) - how FLASH-rish do these (...) (21 years ago, 9-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) Right, see my other post about ARM7 and USB (I wish I knew how to link it but this web interface is killing me!). The biggest issue is one of the devices would have to implement a host constoller interface and a USB storage class driver. (...) (21 years ago, 9-Jan-06, to lugnet.robotics)
 
  Re: new Mindstorms servos?
 
(...) snippy (...) Maybe your complaint is the excessive gearing of the new motor, but otherwise it makes no sense, because the RCX motors are geared too. They are targeted to the vast majority of uses, so most people won't need big geartrains in (...) (21 years ago, 9-Jan-06, to lugnet.robotics)
 
  Re: new Mindstorms servos?
 
(...) And the problem with not gearing down the motors is that for anyhting requiring more than the motors "native" torque, you have to gear them down with those inefficient plastic gears. (...) That assumes that all possible torque/speed (...) (21 years ago, 9-Jan-06, to lugnet.robotics)
 
  Re: NXT - ARM7's and USB
 
In lugnet.robotics, Kevin L. Clague wrote: Your on the right track but your terminology is a little off. USB like many of the next generation protocols is indeed point-to-point. However, the problem is at the protocol level (as you start to point (...) (21 years ago, 9-Jan-06, to lugnet.robotics, FTX)
 
  Re: mindstorms NXT
 
(...) As we currently understand things, the USB port is a 'slave' port - not a 'master' - so you can plug the NXT into a PC - but you can't plug things like thumb drives into the NXT because that would be plugging a 'slave' USB device into another (...) (21 years ago, 9-Jan-06, to lugnet.robotics)
 
  Re: new Mindstorms servos?
 
(...) I beg to differ. The origninal technic motor was ungeared. It was bad because the first thing it did was try to power unlubed high friction gears. At least with enclosed, lubed close tolerance gears, there's a lot less friction in the gear (...) (21 years ago, 9-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT and memory
 
(...) You could - but I might want to store more than one bit of information per square inch (eg a 'confidence' figure or a 'time since last mapped' number - or to store multiple maps so I can see how the map is changing over time). The point is (...) (21 years ago, 9-Jan-06, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR