To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 24264 (-20)
  Re: A LEGO double-throw switch?
 
(...) We can use two polarity reversors to create a three way switch. Set two polarity reversors side by side, linked by an axle. Set it up so that when one reversor is on (no matter the polarity), the other is off. If we drive 9V into both (...) (21 years ago, 23-Aug-05, to lugnet.robotics)
 
  Re: Tripping a relay.
 
Quoting Dan Novy <dan@flashfilmworks.com>: (...) If you mean the coil, 9V is 180% of 5V rated coil voltage. The issue is the total power dissipated in the coil. If you only pulse the relay at a very low duty cycle at room temp, it won't ever build (...) (21 years ago, 23-Aug-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
(...) Okay Brian - an electrical way...and remember, you didn't say "cheap" electrical way... So - we all marvel at the efficiency of Lego motors, right? You could put a motor at the tail end of the conveyor where the crate will hit it...it can be (...) (21 years ago, 23-Aug-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
(...) Ideally I'd like the package/crate itself to throw the switch, probably via pushing on an axle or liftarm extending from beneath. If friction is too low, I can always use a longer lever arm. Another alternative is to have the crate at the end (...) (21 years ago, 23-Aug-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
In lugnet.robotics, Steve Hassenplug (& others) wrote: [snip a bunch of good ideas] Wow, ask a simple question... Currently I'm planning on using one switch that is normally off, and when the forklift delivers a crate it turns it "on-fwd". When the (...) (21 years ago, 23-Aug-05, to lugnet.robotics)
 
  New LEGO RoboCam'Bot
 
Not nearly as unique as the internet controlled RoboCam stacking 'bot, but eh, whatever See it here-- (URL) relabel soon, but JavaCam Push is for Internet Explorer users, and Server Push is for basically everyone else but IE. If neither of those (...) (21 years ago, 23-Aug-05, to lugnet.org.ca.rtltoronto, lugnet.robotics)  
 
  Legway
 
If you haven't heard of Legway, I highly recommend checking it out at www.teamhassenplug.org ...Steve came up with a very cool robot a while back that stands up and balances on two-wheels. I am happy to say that I was able to make Legway work for (...) (21 years ago, 23-Aug-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
(...) Brian - Since I am a spark head...let me just say....this would be interesting. Presumably, you are moving a polarity switch from one "on" position to the next when you hit it...because going to an "off" position would disable the system. (...) (21 years ago, 23-Aug-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
(...) No, because it's only wrong half the time. HOWEVER, now that I think about it, you could mechanically connect two polarity switches together at the end with the motor. Then, instead of connecting one wire from each of the polarity switches to (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
(...) I agree the simplest solution is to use a single switch with one linkage operated by the forklift to switch it on, and another linkage operated by the falling crate, that switches it back off, ready for the forklift. ROSCO (21 years ago, 22-Aug-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
(...) Since turning the 9V wire connectors 90 degrees reverse the polarity, can't you play with how the wires are connected to the switches to re-reverse the polarity on one wire? (...) -Kyle (21 years ago, 22-Aug-05, to lugnet.robotics)
 
  Re: Tripping a relay.
 
If you hit a 5v latching relay with 9v, will it damage it? (21 years ago, 22-Aug-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
(...) Ok, Here's a partial solution (assuming you don't want to mechanically link the ends together). Given: Polarity Switch 1 - rotated forward by Forklift Polarity Switch 2 - rotated forward by crate when it arrives at the end Motor - located by (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
(...) No, I think you should use one polarity switch, without handle to greatly reduce the friction needed to throw it. Putting the crate on the conveyor throws the switch, and when the crate gets to the other end it could push a lever, or better (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
(...) Hi Brian, How will the package arriving at the other end "throw a switch?". Is there enough friction between the package and the belt? Will there be a mechanism in the belt itself to "go halfway and stop"? If you only used one polarity switch, (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
 
  Re: Tripping a relay.
 
Any body know of a typical consumer device that I could hack apart to find 6 to 9V "latching relay" from? (21 years ago, 22-Aug-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
(...) hmm. At first, I would say "No". When you flip your switches at home, the switches could be in either of two states when the lights are "on". (one up, other down OR one down, other up) However, the LEGO polarity switches don't have to act like (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
(...) Yes I'm sorry for not drawing it.. but here goes Imagine you have a cable with ground and a cable with 9V You need two single pole, double throw switches (I don't know what kind lego switches are) For both switches, connect one throw to 9V and (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
 
  A LEGO double-throw switch?
 
So I've got an application where a forklift loads a crate onto a conveyor belt. I could then start the conveyor belt up by having the forklift throw a polarity switch. What I would *like* is that when the crate gets to the other end, it somehow (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
 
  Re: Dual Hex small piston compressor (repost)
 
(...) Hi Kevin, Thanks. I am sorry for the slow feed back. I normally can only check in every week or two as I have no internet at home. Currently, we are on vacation in Lacaster, PA on our way to Ocean City, MD. :) (...) It is my understanding that (...) (21 years ago, 22-Aug-05, to lugnet.technic, lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR