 | | Re: RCX 2.0 Power Supply
|
| (...) A friend did the mistake for me... but I had to repair a few of his RCXs! The connector he used to plug an external supply was prone to be shorted (on RCX side) when he unplugged it. It was only several fuses later that we understood the (...) (22 years ago, 16-Sep-04, to lugnet.robotics, lugnet.trains, FTX)
| | |  | | Re: Lego Compatible (was Re: JCX and Legos...)
|
| (...) (URL) All I can say is wow, and thanks. RoboBrix is a very cool line of products. Have you yet interfaced the h-bridge modules to an RCX output so that it mimics the RCX output? Also, on the shaft encoder board, do you sell any (...) (22 years ago, 16-Sep-04, to lugnet.robotics)
| | |  | | Re: POC Exploration Robot
|
| Mathieu, My replies are mixed in your message, hope they are helpful. --- Mathieu Lalonde <e0nblue@ssl-mail.com> wrote: [[snip]] (...) This is reasonable, since you are talking about two mindstorms kits, plus vision command, though you could use any (...) (22 years ago, 16-Sep-04, to lugnet.robotics)
| | |  | | POC Exploration Robot
|
| <>Hello everyone, I am student in industrial computing (the Quebec counterpart of Computer Science), and I am seriously considering using Lego Mindstorms for my final project. What my teammate and I would like to do is a proof-of-concept exploration (...) (22 years ago, 16-Sep-04, to lugnet.robotics)
| | |  | | Re: RCX 2.0 Power Supply
|
| (...) Not nearly impossible. It just requires a little more intelligence be put into the power supply. All the regulated power supplies my company produces contain a circuit called a down programmer. This circuits job is to discharge the filter (...) (22 years ago, 16-Sep-04, to lugnet.robotics, lugnet.trains)
| | |  | | Re: RCX 2.0 Power Supply
|
| (...) Thanks for pointing that out, Philo. I think I'll stick to the non-hopped up version! :-) (...) Hopefully you didn't find this out the hard way... Mark (22 years ago, 15-Sep-04, to lugnet.robotics, lugnet.trains, FTX)
| | |  | | Re: RCX 2.0 Power Supply
|
| (...) It is nearly impossible to build a power supply that puts out the rated voltage when there is no load. Most will put out too high a voltage (like you have seen), some just shut down. To meassure the voltage of a PS, shorten it with a 1000 Ohm (...) (22 years ago, 15-Sep-04, to lugnet.robotics, lugnet.trains)
| | |  | | Re: RCX 2.0 Power Supply
|
| (...) Indeed, the input capacitor of the RCX is rated 10V, so I would not do that for a too long time. This 1000µF capacitor, used to keep memory during battery exchange, is directly connected to RCX board supply input. By the way, this capacitor is (...) (22 years ago, 15-Sep-04, to lugnet.robotics, lugnet.trains, FTX)
| | |  | | Re: Lego Compatible (was Re: JCX and Legos...)
|
| Joe: I was hoping more people would chime in. Alas, I do not see much interest in this thread right now. Please accept my apologies in advance, my comments below are going to sound like an advertisement ... (...) Such a system already exists and it (...) (22 years ago, 15-Sep-04, to lugnet.robotics)
| | |  | | Re: RCX 2.0 Power Supply
|
| (...) You need to check the voltage while the PS is under load. Pretty much every power supply puts out more when the load is low or nothing. Has to do with loads of factors, but mostly quality of the PS (and (thus) internal resistance of the PS) (...) (22 years ago, 15-Sep-04, to lugnet.robotics, lugnet.trains)
| |