To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 22559 (-10)
  Re: BrickFest is coming!
 
I'm reposting this message to the events.BrickFest list so that everyone knows about this great opportunity. I'm sure there are others out there, just like me, who have an RCX set (found for a good price, or a gift, whatever the case...) and you (...) (22 years ago, 25-Jun-04, to lugnet.events.brickfest, lugnet.announce, lugnet.technic, lugnet.robotics)
 
  BrickFest is coming!
 
... and there are competitions to be entered and won! Check out the Events at www.brickfest.com There's a link via Mindstorms Competitions to the event descriptions and from there to the rules pages. So read them and start building! ... there are (...) (22 years ago, 22-Jun-04, to lugnet.technic, lugnet.robotics)  
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) It will help us help you if you list the resources you have and how many of these you need to make. If your resources are limited, you may have to use a few different solutions to match your inventory. Kevin (22 years ago, 20-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) bricks along the beam, like I did on my tower crane (URL) (22 years ago, 20-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
"Brass Tilde" <lego-robotics@crynwr.com> wrote in message news:00a301c4552c$24...hps.net... <snip> (...) I built something very much like this. I used a rack with a few 1x1 TECHNIC beams in it. The touch sensor pressed against the side of the rack (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  RE: is it possible to make a motor with a limited range of travel?
 
(...) belt. (...) Hello, If you take a beam and put racks on it, you can push that across a gear and it will make the gear spin. A back and forth motion causes back and forth rotation on the gear. To get mechanical back and forth motion, simply (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) There are some methods involving non-lego peices in the mix. One such method, is to build a touch sensor using a microswitch from a mouse. Wire this in the normally closed way - so when it is activated, it will open. So the motor will go the (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) Or you may use poor man's clutch gear: pulleys and slipping rubber belt. Or if your application does not need too much mechanical power, you can simply use a low power level on RCX output. With a power level 2 both the RCX and the motor can (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) clutch (...) at (...) You should only need one touch sensor per rack. If you only have one motor per rack, then you should be able to use one sensor per motor (unless you have other stuff you need the sensor ports for, of course). M RRR...RRR (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) Thats kinda usefull except that I dont have enough clutch gears, touch sensors or sensor inputs on my RCX :( (22 years ago, 18-Jun-04, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR