To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 1826 (+10)
  Re: R/C Servo to Legos
 
John Kittelsrud writes: > Does anyone have a solution for coupling the output of an R/C servo > to something like a Lego axel? I did it using an axle stopper glued on with hot-melt glue. Worked fine until I would over-torque it. (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  lego train and motors
 
Hi all. I received a cargo train for Christmas and was experimenting with the motors and speed control unit. I would like to incorporate the tracks and railway motor into some RCX projects in the near future. When I hook a regular lego motor (the (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
(...) something like a (...) The usual way the RC community does it is to use a cover from a auto tire valve stem, fill it with epoxy and push it over the splines of the output shaft. Be careful that no epoxy runs down into the bearing of shaft :-). (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  sensor details
 
Do the sensors read voltage or measure resistance? or both? chris (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Sensor ideas
 
Looking at some of the ideas for multiplexing touch sensors gave me a couple of ideas - I may not get around to constructing these anytime soon so if someone wants to run with them I'd sure like to hear how you did. Idea #1 - Whisker sensors using (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
 
  Re: Mindstorms CD and Soft Windows
 
(...) It seames to be not possible to use these emulators. I've tried them all and is doesn't work. Though the software will run, the hardware won't. There are two options: use Robolab from pitsco-dacta or use Not Quite C from Dave Baum (you can (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
I use epoxy to glue on assorted pieces where I need them. If you use enough epoxy to fill the space completely, you can snap off the piece and then you have a workable Lego bump impression. What I have found with epoxy is that the epoxy holds just (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Voltage or resistance
 
After experimenting with various photo sensors, it appears that resistance is what is measured. Solar cells produce no change in readings, but CdS photo resisters do. I managed to hook up a BASIC STAMP (a small microcomputer by Parallax) to one of (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  The Bed Mill
 
I have posted some pictures of my latest mill at (URL) I will post a QuickTime movie when I complete the program and make a real cut. Bob (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: Voltage or resistance
 
I'm joining this thread a little late, so sorry if any of this has already been stated... For "passive" sensors, the RCX measures a voltage level, but since there's a pullup you may not get what you expect. If memory serves, the RCX ADC uses a 5.0V (...) (28 years ago, 27-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR