 | | Re: Robotics sub-groups
|
|
Hi Todd, I've received several requests to set up a dedicated legOS mailing list. A while ago, you suggested setting up a subgroup, and I'd like to take you up on your offer. Could you create something on the lines of lugnet.robotics.legOS? Thanks, (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Recommended Add-On Sets?
|
|
I know this has been posted before but, can anyone suggest some add-on kits, spares, technic kits to enhance the basic Midstorms starter kit? Sources and phone numbers would be a great help. I've got the Dacta catalog if you need to reference (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
(...) I'm in the process of writing a web page on that very subject - it'll probably still be a couple of days away, but should at least be a starting point. Stuart -- Did you check the web site first?: (URL) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Recommended Add-On Sets?
|
|
# I know this has been posted before but, can anyone suggest # some add-on # kits, spares, technic kits to enhance the basic Midstorms starter kit? # # # Sources and phone numbers would be a great help. I've got the Dacta # catalog if you need to (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Sensors
|
|
(...) Jasper - for newer keyboards this is true - but your probably showing your age here :) Most of the early keyboards were discrete switches (Apple, Dec, IBM) It was after a while that the 'film' switches became available. I've had 1,000s of the (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: shaft encoders for a track drive
|
|
Steve Wall wrote: <snip> (...) I've had good results using Hall effect magnetic sensors. I found some 0.1" dia. disk magnets at the hobby shop and embedded them into the holes in some Lego Technic pulley wheels. It's true that only about three (...) (28 years ago, 16-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
(...) You can try: (URL) for a UK version of the supplementary catalogue. I do have an international version too, but it doesn't cover USA. Personally, I would recommend some pneumatics and some of the cannons from the competition sets (for fun). -- (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | S19 disassembler
|
|
Will someone please point me to an S19 disassember TIA, - - - Nick - - - (28 years ago, 16-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Serial Communication between HBs HELP!!! (Again)
|
|
Hi, I am trying to get communication working between two HBs via the RJ11 serial port. I read the FAQ on the HB web site and I have the right cable. On the trans. HB the power LED blinks which indicates it is transmitting. Also whenever I turn on (...) (28 years ago, 16-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
(...) I purchased the RIS and the Robosports expansion kit, and then ordered the following to fill it out: Lego Dacta 800/362-4308 ===...=== 2x N979891 9V Angle Sensor 2x N779945 Differentials 2x N779932 Black Plates 2x N779876 Large Turntables 2x (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|