To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *9231 (+10)
  I2C bus with the Handy board ?
 
Hi! It is possible to use component with I2C bus on the Handy board ? Do you know this ? some examples : PCF8584, PCD8574, PCF8591...... I'd like to use many component with this bus. Can you help me (if it is possible) ? thanks Dperonne@aol.com (28 years ago, 14-Feb-99, to lugnet.robotics.handyboard)
 
  Re: Robotics sub-groups
 
(...) Well, I want the resolution that's most beneficial to the individual projects and most enjoyable for participants. Fine resolution is good as long as it lives up to the promise of providing for more focused discussions but bad if it is so fine (...) (28 years ago, 14-Feb-99, to lugnet.admin.general, lugnet.robotics)
 
  Serial Communication Please Help!
 
Hi, I am trying to get communication working between two HBs via the RJ11 serial port. I read the FAQ on the HB web site and I have the right cable. On the trans. HB the power LED blinks which indicates it is transmitting. Also whenever I turn on (...) (28 years ago, 14-Feb-99, to lugnet.robotics.handyboard)
 
  RCX Assembler programing
 
I'm using the RCX together with the Spirit OCX and VB 5. But it seems to me as the Spirit OCX has the comfort of machine language and the flexibility of standard basic. So I would like to have a more powerful and flexible tool for the programming ( (...) (28 years ago, 14-Feb-99, to lugnet.robotics)
 
  Re: An untested idea...
 
This sounds like an old Lionel(sp?) train's forward-neutral-reverse switch. Anders Isaksson wrote in message ... (...) (28 years ago, 14-Feb-99, to lugnet.robotics)
 
  Re: Expansion board questions
 
Hi Duncan, I would like to have a copy of your hbtest.c to test the expansion board. If you could post it I bet a lot of us would use it to test. Thanks in advance Terry G. ---...--- (...) doesn't (...) which (...) the (...) the (...) height (...) I (...) (28 years ago, 15-Feb-99, to lugnet.robotics.handyboard)
 
  Re: Expansion board questions
 
(...) Terry, I will send you the code. I sent it to Fred for the website but haven't heard back. I'm reluctant to post it to the list, but I will mail it to anyone who asks... Best, Duncan (28 years ago, 15-Feb-99, to lugnet.robotics.handyboard)
 
  Sensors
 
I am gathering parts to make sensors and was wondering if anyone has a good source for small microswitches ( for tuch sensors) and also LED lights 9 to 12 volt. Thanks in Advance Jim Clark ---...--- This message was sent from Bess.Net, a filtered (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  Expansion board test routine
 
Hello all, Well here it is, for what it's worth. The functions are pretty obvious, it works just like the original hbtest.c that Fred wrote. To try servos other than #5, you'll have to edit the line: servo5=(16*knob()); In the test_servo() routine. (...) (28 years ago, 15-Feb-99, to lugnet.robotics.handyboard)
 
  Re: Sensors
 
I found every thing I needed as far as the light sensors at Radio Shack. I don't know where you're located, but here in California, Fry's Electronics is the place to go. You can get everything you need from parts, boards, and the junk food to eat (...) (28 years ago, 15-Feb-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR