 | | Re: Interactive C - Preprocessing?
|
|
Hans, Thanks for this. Actually, I am now using the CPP that comes with the GNU-C / AS11 set for the PCODE & *.ICB re-compilation. I call my real source *.IC and pre-process it into *.C, then let IC load that .C file. I am winning in a clumsy way I (...) (30 years ago, 6-Nov-96, to lugnet.robotics.handyboard)
|
| |
 | | Polaroid Sonar Ranging Module
|
|
Hi ! Again this is a question about the Polaroid Sonar Module. Some times ago I disasembled a partly dead Polaroid camera and now I have a neat little board with the sonar transducer conected to it. I even have schematics for this board (thanks to (...) (30 years ago, 6-Nov-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: "Mobile Robots: Inspiration to Implementation" for FIVE BUCKS!!
|
|
(...) Joseph L. (...) $44.00, can be (...) Bookseller, Falls (...) condition. I (...) one I rated (...) Board, and (...) Well, I would like to order this book from France. Has anyone an e-mail address or a fax number so that I can place my order? By (...) (30 years ago, 7-Nov-96, to lugnet.robotics.handyboard)
|
| |
 | | Mini Board or Handy Board?
|
|
I am just getting into robotics and microcontrollers, and have run up against a brick wall. After gathering information on both the Handy Board and the Mini Board, I am unable to decide which to build first. Money is somewhat tight, so whatever (...) (30 years ago, 7-Nov-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Mini Board or Handy Board?
|
|
(...) A little background, my first robot controller was the 1802 based ELF processor ca. 1979, it didn't do much. The first mobile robot I built was tethered to a Heathkit H-8. The first untethered robot used a Xerox 820 mainboard, and a lot of (...) (30 years ago, 7-Nov-96, to lugnet.robotics.handyboard)
|
| |
 | | error message
|
|
Hello everybody, Whenever i load any program to the handyboard the following message is displayed " IC is now dangerously running low on memory. Yous should makesure that your PC has atleast 550-600K of lower memory free before staring" iam using a (...) (30 years ago, 7-Nov-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Mini Board or Handy Board?
|
|
(...) In answer to your last question, the best price I have seen for the MC68HC11E1FN is at B.G. Micro for $6.95 if my memory is correct. I have dealt with them before and not had any problems so far. You can check the price on their web page at (...) (30 years ago, 7-Nov-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: "Mobile Robots: Inspiration to Implementation" for FIVE BUCKS!!
|
|
(...) I like the book "Sensors for Mobile Robots" by H.R. Everett. It doesn't have alot of microrobtics in it but is good for theory and to build you a foundation in Robotics Technology. (30 years ago, 8-Nov-96, to lugnet.robotics.handyboard)
|
| |
 | | DS1233-10
|
|
Hello everybody, HELP HELP HELP ... I can't found the Dallas 1233-10 circuit in Belgium, it's the only part I need to continue my HB to the end. BUT I found an IC from Maxim that could do the job, is it true? This part is the MAX809L (threshold of (...) (30 years ago, 8-Nov-96, to lugnet.robotics.handyboard)
|
| |
 | | Run Time error 1
|
|
Hello, I'm new at IC and I don't really know how to fix all the errors yet. Can you please download the attached file and look it over for any problems and tell me how to fix the Run Time Error 1. Thank You, Peter Eacmen (30 years ago, 8-Nov-96, to lugnet.robotics.handyboard)
|