To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8321 (+10)
  CONTINUOUS BEEPING
 
Dear Fred Martin/friends, We have put a total of 6 chips on the handy board-the 6811 ,two chips placed side by side to the left of the 6811, the fat chip on the upper side of the 6811, two ICs(chips) one on each side of the fat chip.(component side) (...) (28 years ago, 23-Jan-99, to lugnet.robotics.handyboard)
 
  DATALOG and C
 
Hi all, Could someone write a C program that just hangs out and waits for the RCX to send a datalog to it? RCXLOG is great but not quite what I need. RCXLOG.exe Tells the RCX to upload a datalog, prints it out, then quits. I'd like something that (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: mouse
 
(...) Personally, I've never been able to figure out just jow a mouse does that, either :) Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: DATALOG and C
 
Brandon wrote in message <36A93B81.4F96@sprynet.com>... (...) I doesn't work that way. The RCX sends up to 50 data points at a time when it sees the UploadDatalog command. The RCX won't do anything thing like that from a program. The UploadDatalog (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: expansion ports
 
(...) I can make the same case about something they _do_ have a patent on... say, the 12-tooth bevel gear, is pretty new. Does that come with a patent? (...) Devil's advocate. Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: homebrew Temp sensor
 
(...) I damn well know what an elco is, thank you, and, I've never seen one blow up from <12V.. they can get a bit hot, and make a little plop, but I've personally never seen them shower the room with shrapnel. Which of course, is not saying that (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: Pneumatic Tanks
 
(...) The heroine dealer on the corner? Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: Toy motors
 
right, this is a good answer. you buy a device called an "electronic speed controller". this connects like a servo to the HB (3 wire connection) and has outputs to drive high current DC motors. you also connect a separate power supply to the device. (...) (28 years ago, 23-Jan-99, to lugnet.robotics.handyboard)
 
  Re: Working around the 3 output limitation
 
(...) The one with two studs in the middle, and two holes at the ends? and you then have one of the half-bushings with teething (1) thaty it rests on? I would say that those teehings are too deep too slip comfortably, but I haven't tried it out. (1) (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: Toy motors
 
sorry, send my msg before it was done. right, this is a good answer. you buy a device called an "electronic speed controller". this connects like a servo to the HB and has outputs to drive high current DC motors. you also connect a separate power (...) (28 years ago, 23-Jan-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR