To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6831 (-10)
  sensor connectors
 
I've been reading the pages on making sensors. Does anyone know the details of the sensor connectors. Most of the sensors have two contacts, while the RCX connectors have four. I would think that one of these four must be a power pin and one must be (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
 
  RE: servo motor
 
Since the System 3000 servos appear to be made by Futaba, and they specify a standard Futaba "J" connector, my guess is that they would plug right in. Futaba practice is as you state: red=5V, black=common, white=signal. Brett Anthony -----Original (...) (28 years ago, 26-Dec-98, to lugnet.robotics.handyboard)
 
  Mindstorms CD and Soft Windows
 
Will a translation utility such as soft windows; Virtual PC allow me to runt he Mindstomrs Windows 95 CD from my G3 Mac? (28 years ago, 26-Dec-98, to lugnet.robotics)
 
  Re: CHARGER BOARD PROBLEM(URGENT)
 
phillip, please go through the sequence of tests in the assembly directions (as if you were building the serial/charger board from scratch), and indicate the point at which you first detect a problem. (URL) your message you said: (...) (28 years ago, 26-Dec-98, to lugnet.robotics.handyboard)
 
  Re: legOS problems
 
(...) How are your batteries? I've found out that with my CyberMaster and with almost spent batteries, when a motor worked with a bit more load than was supposed, the unit shutdown entirely and it loose all memory in the process. Because it's a RCX (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
 
  Re: Slightly off topic - How to access game port & joystick from Visual Basic
 
(...) I don't know if this is helpful, probably not, but if it was in C++ I would tell you to give a look at the Multimedia extensions "mmsystem.h" and "winmm.lib". Laurentino Martins *<||:-) [mailto:lau@mail.telepac.pt] [(URL) (28 years ago, 26-Dec-98, to lugnet.robotics)
 
  Re: legOS problems
 
I had this problem when using the rcx utils to do the firmware download. I switched to using Kekoa's firmdl and that worked fine. What program are you using to do the firmware download? -brian (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
 
  RE: Slightly off topic - How to access game port & joystick from Visual Basic
 
You can find routines at (URL) Message----- From: Don Hewitt [mailto:donhewitt@wo...t.att.net] Sent: Friday, December 25, 1998 7:15 PM To: lego-robotics@crynwr.com Subject: Slightly off topic - How to access game port & joystick from Visual Basic (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
 
  legOS problems
 
when I send a new set of firmware to the rcx unit, download seems to work fine, but the rcx unit powers off at the end of reception and requires a battery removal to get it to even power back on.. I built the tools under winnt using cygwin32 b20.1, (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
 
  Re: Downloading problems
 
Use 6811 Downloader to download pcode_hb.s19. Power cycle, and the Handy Board should beep and display a version message on its LCD screen. Then, run IC modem or IC printer depending on which port you are using. It should be configured to boot with (...) (28 years ago, 26-Dec-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR