 | | RE: Limited number of MindStorms??
|
|
The Wall Street Journal says Lego will sell 80,000 by years end and they still can't meet the global demand for these things. Their marketing folks thought they'd only sell 12,000 the first year. Guess they didn't count on the over 30 crowd still (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Limited number of MindStorms??
|
|
(...) It ain't so. That's all they planned to make by the end of this year. (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Replacing L293D with L298H
|
|
Hi Fred and others, I very desperate to debug the problem that took place in my HD. When I download the P_code, it is successfully downloaded. However, when the next instruction ask to reset the board, no words of sentence appear on the LCD. Only 16 (...) (28 years ago, 18-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Downloader and a/d
|
|
Cesar, (...) According to my book, you can set the reference voltages to anything from Vss to Vss + 6.0 V (notice that this is higher than Vdd). The A/D result is a ratioatic comparison for the sample voltage to the references. Page 48 of the (...) (28 years ago, 18-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | All-around-the-robot bump detection
|
|
For those of you with LEGO pneumatics, I've got a question. There seems to be a need for an all-around-the-robot bump detector. Would this work? Wrap soft rubber tubing around the robot, seal one end of the tube, and connect the other to a pneumatic (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: All-around-the-robot bump detection
|
|
(...) Nice idea, just one problem though... It gives you no idea as to the direction of the collision so the robot would need some other means of locating the cause of the collision and taking remedial action. Still, if you can solve that problem... (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
The tubing is such a small diameter that I think it would take a large surface of contact for enough air to be displaced to move a pneumatic cylinder. Maybe with not-Lego(tm) tubing that was, maybe 1/4 to 1/2 inch [6.35 to 12.7 mm :P ] in radius (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
Oh yeah, that too. :) Jeremy Morton a-jeremm@microsoft.com -----Original Message----- From: Fred Read [mailto:fred@corp.ne...om.net.uk] Sent: Friday, December 18, 1998 6:10 AM To: lego-robotics@crynwr.com Subject: Re: All-around-the-robot bump (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: All-around-the-robot bump detection
|
|
(...) I haven't actually tried this, but I can hardly imagine that the pressure generated from just squeezing one small part of the tube is sufficient to extend a cylinder and press a touch sensor. The pressure generated will probably just "vanish" (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
Hmmmmm, It's morning and I haven't had coffee yet so bear this in mind but it seems to me that this is a) a fairly cool scheme for post collision detection, and b)expandable to support direction detection through the use of 4 sensors. Imagine that (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|