To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5421 (+10)
  Compling *.ICB files
 
Hello, Does anyone have any tips on compling *.ICB files on Windows NT? I have IC 3.2. Using the as11_ic.bat file works with much modifications to the the *.asm files. The web based complier at Newton Labs compiles the code, but loading the ICB file (...) (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
 
  Re: gear differential [URL]
 
Hello, all... I was the one that brought up using a gear differential to solve another's problem. Here is a URL of a better design than mine. (URL) you. PS: new project Got the idea looking at the design for a Lego Joystick... Robotic Fencing! 3 (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
 
  Re: gear differential [URL]
 
(...) experience with this is kinda bad. I once did something quite similar, but when the drivetrain was loaded, one of the motors reversed, making the diff output zero. This happened, BTW, when I geared down the motors by 3:1 before passing the (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
 
  Re: Building gcc
 
YES, now i added the bin directory with the sh in it ! Configure now works fine, but make complains about some bfd.h missing (and no rule to make it) in bfd Directory ! There is a bfd-in.h and a bfd-in2.h but no bfd.h. I tried configuring the whole (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
 
  serial communication
 
Hi, Does anyone know the what is the most suitable port settings to use ? The Bits per second, number of data bits and stop bits, parity bit and the flow control type. Thanks for helping... (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Building gcc
 
Hello, Some time ago I tried to compile binutils 2.9.1 for H8/300 with cygwin on NT and I was also getting compilation errors. People from the binutils development team (Ian Lance Taylor, ian@cygnus.com and Kai Ruottu, karuottu@freenet.hut.fi) (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
 
  Re: One tip, and a few questions.
 
(...) 0-100. 100 being very very bright. (28 years ago, 20-Nov-98, to lugnet.robotics)
 
  Re: Sharp IS1U60 availablity
 
Check B. G. Micro 800-276-2206 www.bgmicro.com I would not be too concerned with the actual part number, just look for an Infared sensor or remote control sensor. Also get the pin outs as these may be different. Also have you considered using fewer (...) (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
 
  Re: motor port problem .
 
Philip In a message dated 98-11-19 21:05:04 EST, you write: << hi, I have a big problem. I followed the method of yours that just lift up pin 8 of one L293 and wirewrapped it. The positive supply is wirewrapped to pin 8 . How about the negative (...) (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
 
  TEST
 
TEST (28 years ago, 20-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR