To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5416 (+10)
  Re: motor port problem
 
hi Fred, Why there is 2 holes each for the positive and negative supply on the pin jack (J13)? I thought that just insert one hole each for the positive and negative supply only. I need to know why the J13 is designed for 1x4 holes before i decide (...) (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Building gcc
 
(...) It sounds like you don't have CygWin32 configured correctly. Ideally you should have a directory "/bin" that has "sh.exe" in it. If you have that, then bash will run scripts correctly. In my case, I ran "bash" then used the "mount" command to (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
 
  Best Lego Kit with Micro-motors
 
Hey folks, I need to couple more micro-motors. What would be good kit to buy to get those and other good stuff. Pneumatics would be wonderful. I'm not familiar with the current kits, so I need advice. Thanks, David (28 years ago, 20-Nov-98, to lugnet.robotics)
 
  Arithmatic operation
 
Hi all, I am dividing 4.1 by 4.1 in following manner and getting answer 2. instead of 1. Dividing 4.2 by 4.2 give 1 result, dividing 4.6 by 4.6 again give 2. Except 4.1 and 4.6 rest all numbers give 1 result. I am using IC 3.2. Any help in this (...) (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
 
  arithmatic operation(more)
 
Hi all; I have also reckon that following numbers are also giving 2 in answer if divided by same numbers. 5.1,6.1,7.1,4.6,5.6,....4,1.92.3, 2.8,3.3,3.8,8.2,8.7,...10.2,10.7, thanks javaid iqbal (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
 
  Compling *.ICB files
 
Hello, Does anyone have any tips on compling *.ICB files on Windows NT? I have IC 3.2. Using the as11_ic.bat file works with much modifications to the the *.asm files. The web based complier at Newton Labs compiles the code, but loading the ICB file (...) (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
 
  Re: gear differential [URL]
 
Hello, all... I was the one that brought up using a gear differential to solve another's problem. Here is a URL of a better design than mine. (URL) you. PS: new project Got the idea looking at the design for a Lego Joystick... Robotic Fencing! 3 (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
 
  Re: gear differential [URL]
 
(...) experience with this is kinda bad. I once did something quite similar, but when the drivetrain was loaded, one of the motors reversed, making the diff output zero. This happened, BTW, when I geared down the motors by 3:1 before passing the (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
 
  Re: Building gcc
 
YES, now i added the bin directory with the sh in it ! Configure now works fine, but make complains about some bfd.h missing (and no rule to make it) in bfd Directory ! There is a bfd-in.h and a bfd-in2.h but no bfd.h. I tried configuring the whole (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
 
  serial communication
 
Hi, Does anyone know the what is the most suitable port settings to use ? The Bits per second, number of data bits and stop bits, parity bit and the flow control type. Thanks for helping... (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR