 | | Re:
|
|
Hi everyone, The mistake you make in your calculation is that in your calculation you take the entire 15V for the resistor and this leaves no voltage for charging your NiCad. Do the same thing again and deduct your NiCad voltage from the 15V you (...) (28 years ago, 14-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
Daniel Miller wrote in message ... (...) What? (...) This is all fine and well, but I was thinking about something a little less complex. The RCX doesn't have the power to perform image processing and sophisticated feedback control. What I was (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) 1) You've been playing too much Carmageddon. 2) Control theory is relatively new (it paces the development of computers). There are quite a few good textbooks available, but a professor is a much greater help. Familiarity with calculus and (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
Ardjan Besse wrote in message <364c7d42.4532817@lu...et.com>... (...) "Straight" is a relative term. For example, while the alignment might be 0straight, the wheels might not provide the bot with the ability to travel in a straight line. I believe (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
Alex Wetmore wrote in message <008601be0f2a$01b821...ft.com>... (...) This would give you a good turning radius. However, it would take the bot a long time to turn. (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | MindStorms on NT / trouble posting to the list
|
|
I'm posting this question on behalf of peterbag@microsoft.com. Please direct replies to that address... Peter asks, Help! I am considering purchasing a MindStorms kit tonight, but I want to make sure it will run under WindowsNT. Has anyone done (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | RE: Homebrew sensors?
|
|
Why would you need an array to do that? You could do it with three variables: var1 = starting angle var2 = highest amplitude encountered so far var3 = angle of highest amplitude The algorithm goes something like this (in pseudo-C): var1 = (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Homebrew sensors?
|
|
(...) Unfortunately the bang comes with the whoosh, often leading to a rapid unplanned dissasembly. Witness the recent destruction of Delta III #1, caused by a 4hz roll oscillation, or the Titan IV that ended in a BFRC due to a clog in its wacky (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Homebrew sensors?
|
|
(...) I was thinking of something that sensed amplitude, not frequency. (Like the light sensor, which sees brightness, not color.) Of course, whatever you want for yourself is best. :) I know the logic of taking two sensors and differentiating to (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | RE: coasting moters in nqcc
|
|
Hello all, In reading about moving in a straight line tread there was an issue related to the motor being off, on, or float. If off sets into brake mode and float does really turn them off. I thought that using float for time that the motors are (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|