To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *4866 (+10)
  programming help.
 
hello can someone please tell me what does the following command line mean? bit_set(0x0e, 1 << (4 + motor)); i know that 0x0e refers to memory location $0E but how does bit_set work? is it similar to poke? and more importantly, what operation does (...) (28 years ago, 31-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Mailing List
 
I used to work at AOL technical support, I would be very much interested if you could figure out how to use AOL as a POP3, AOL is NOT a POP3 server. AOL is very proprietery, one of the many reasons (and doesn't support DUN - dial-up networking) that (...) (28 years ago, 1-Nov-98, to lugnet.robotics.handyboard)
 
  code segment
 
Hi all, I have writen a code, when i download it i received following message. "c:\ic\libs\speed.icb(1): Code and data segments collide -- overflow of 681 bytes" After that I reduced the size of code and downloaded it, It was successfull. I got (...) (28 years ago, 1-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Voltage for the DC motor
 
(...) Sorry, I cannot help you. My board look exactly like the one on the picture. It's a Handy Board v.1.2 I bought assembled from Glasson Research. Does somebody knows what board Phillip is using? -- Eric (28 years ago, 1-Nov-98, to lugnet.robotics.handyboard)
 
  as11_ic
 
(...) (28 years ago, 2-Nov-98, to lugnet.robotics.handyboard)
 
  Re: IR Detection
 
Hi Most of the IR LED's sold at Radio Shack are the 840-880 nm wavelenght type. The Sharp tin can requires the 940 nm wavelength IR beam if my memory serves me right, it also requires to be modulated at 38 or 40 kHz depending on the model. This 38 (...) (28 years ago, 2-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Automated brick sorter
 
Huw, Very nice job. I saw that you used a clutch gear. On thing I've been experimenting with is replacing a clutch gear with a pair of motors, one working like a generator to drive the other. This only works well if the generator-half is one of the (...) (28 years ago, 2-Nov-98, to lugnet.robotics)
 
  Re: Bend/ Flex Sensor
 
I think its cheaper to get an old Nintendo power glove and Hack it! (...) (28 years ago, 2-Nov-98, to lugnet.robotics.handyboard)
 
  Re: programming help.
 
The "<<" is a shift left operator in C 0E is the actual motor port on the Handy Board. (...) mean? (...) between 4 and 7. (...) peek(address) | value). I don't have any documentation here, so I don't know what is stored in 0x0e, but it could be the (...) (28 years ago, 2-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Voltage for the DC motor
 
Ja, I could not tell you for the life of me what 'type' f a HB it is, but I remember someone once telling me that you could just remove one of the pins from the driver chip instead. This method would be less final (ie, just bend the lead up and if (...) (28 years ago, 2-Nov-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR