To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *4746 (-10)
  Dead HB
 
Hi All, While I was building my sumo robot I managed to short a wire in my HB. I put a wire that was connected to a multimeter and also connected to another part of the robot, into a digital sensor input, sparks came out and it smelt like burnt (...) (28 years ago, 22-Oct-98, to lugnet.robotics.handyboard)
 
  Read A/D converter
 
"HI" , I am trying to read the A/D converter but the program gets "Hung-Up" on the line "ANALOOP", the CCF bit never sets. Please give me a hint. Here is the Assembly code. /* MAGLEV.ASM, Magnetic Levitation by Hector Noriega, 28JUNE1998.*/ /*Handy (...) (28 years ago, 22-Oct-98, to lugnet.robotics.handyboard)
 
  train AC adapter for RCX?
 
Hi, Someone may have mentioned this earlier... The AC adapter port on the RCX indicates a 9-12V AC input. Does this mean it'll work with the train regulator AC adapter? Thanks, -Tim (28 years ago, 22-Oct-98, to lugnet.robotics)
 
  Re: Basic Sensor Question
 
if a sensor connector row looks like this -- [ ][ ][ ][ ][ ][ ][ ] [ ][ ][ ][ ][ ][ ][ ] [ ][ ][ ][ ][ ][ ][ ] 6 5 4 3 2 1 0 then to connect to sensor 0, you plug the switch into the places marked "[X]": [ ][ ][ ][ ][ ][ ][X] [ ][ ][ ][ ][ ][ ][ ] [ (...) (28 years ago, 21-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Basic Sensor Question
 
You were right, also it seems my board is wired incorrectly analog(0) controls the connector marked 7 on the hb. Thanks for your help! Julian -----Original Message----- From: Scott R. Harris <srharris@phoenix.Pr...ceton.EDU> To: Julian Porter (...) (28 years ago, 21-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Basic Sensor Question
 
It sounds like you've got the switch between +5V and GND. What pins exactly are you connecting to? The sensor connections Are like this: _ _ _ G + I N 5 N D V P You dont need a resistor to use a microswitch. The HB inputs have pull-up resistors, so (...) (28 years ago, 21-Oct-98, to lugnet.robotics.handyboard)
 
  RE: RTOS for HB?
 
There is the Micro Kernel from Jean J. Labrosse. It's a free kernel readily available, also for the 68hc11. I have his book but haven't implemented the full kernel yet, only parts of it. Its well written and cheap. Look at: (URL) jaron paludanus (...) (28 years ago, 21-Oct-98, to lugnet.robotics.handyboard)
 
  Basic Sensor Question
 
I just got my HB and am trying to test the sensor input, the docs say to hook up the microswitch between signal and ground, when I do this and close the switch my hb resets (because I just shorted it out...). I tried putting a resistor (330 ohm) in (...) (28 years ago, 21-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Charging batteries
 
(...) Well I will be the first to admit that this is hardly a scientific study but here is my personal experience. For 4 years I have had the same cellular phone and the same notebook computer. The cellular phone is a Motorola with an Intelecharger (...) (28 years ago, 21-Oct-98, to lugnet.robotics)
 
  Re: Questions about sensors
 
Eric Noyau wrote: <snip> (...) The results you get from a reflective IR sensor will vary quite a lot depending on surface color, roughness, angle of incidence, electrical noise, etc. My IR sensors were not good for much of anything besides encoders, (...) (28 years ago, 21-Oct-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR