 | | Re: Power Function control with RCX and BrickOS
|
|
(...) Glad it worked for you and thanks for the heads up on the RCX 2.0 problems. i don't have a 2.0 RCX to play with so i'm not sure if it is a timing issue that can be resolved or what. i was very excited the first time i got my RCX to talk to the (...) (19 years ago, 26-Jan-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Power Function control with RCX and BrickOS
|
|
(...) Well this was just a quickly hacked out example program to show how to use the library function that i wrote. i realized at the time that the PWM started out at fastest and went to slowest but i had run out of steam and never really got back (...) (19 years ago, 26-Jan-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics, FTX)
|
| |
| | NXT Power Programming > LDD files?
|
|
Yesterday, I acquired and am sharing John's book "NXT Power Programming". I tried to read as much of it last night. Great book! Anyway, I'm at PSU conducting a Lego NXT class with 7 boys. Several of the kids are very interested in the Remote Control (...) (19 years ago, 26-Jan-08, to lugnet.robotics.nxt)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) Absolutely excellent news! Downloaded and printing... (19 years ago, 26-Jan-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics, FTX)
|
| |
| | Re: Power Function control with RCX and BrickOS
|
|
Thank you very much for that fine piece of software Bob! After reading your post I immediately run in my LEGO room to grab an RCX and the IR tower to test your software. Well, I had to find out that I had not enough batteries at home and thus had to (...) (19 years ago, 26-Jan-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics, FTX)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) I did this experiment a while ago, I just presumed everyone else has as well. The Short answer is NO. I could not get the new IR train to control the PF receivers either at full on, or with PWM. My IR train, and PF gear are 100% incompatible. (...) (19 years ago, 26-Jan-08, to lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Power Function control with RCX and BrickOS
|
|
(...) Okay, thanks. I can get 'Single output Mode' to work now. 'Single pin Mode' may be working too, but I'm not sure what to expect from it. I would expect setting either C1 or C2 would set them to 9V and run a motor forwards or backwards. Setting (...) (19 years ago, 26-Jan-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics, FTX)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) I'd be very interested in that experiment (using a Hobby train RC on the PW Receiver) as well, but this does answer a number of questions for trains. For instance, tunnels and large layout out of line-of-sight on the RC should now be possible. (...) (19 years ago, 26-Jan-08, to lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) Either single pin modes allow to set each output to 1 (9V) or 0 (0V). (...) See the drive datasheet: (URL) can reach 1A peak, continuous value is lower (500-600mA) especially if both outputs are heavily loaded at the same time. Philo (19 years ago, 26-Jan-08, to lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Power Function control with RCX and BrickOS
|
|
(...) Bob, I could not wait to get home from work to try this. I want to say thank you; your effort has saved me many countless hours. I loaded the Firmware, and the Program into a 1.0 RCX, and the brick worked flawlessly! On my 1.0 brick, I was (...) (19 years ago, 26-Jan-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics)
|
