To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *45719 (-10)
  Not eXactly C beta news (NBC)
 
I have just released a new beta of NBC with built-in support for 3 programming languages targetting the standard NXT firmware. This beta release focuses primarily on improving the Not eXactly C (NXC) programming language support in the compiler. It (...) (20 years ago, 12-Dec-06, to lugnet.robotics.nxt, FTX) ! 
 
  Re: Locked motor
 
I can't believe I didn't find the description on your site. It was the first place I looked!! Since no easy repair appears to be possible I've contacted the seller who has graciously accepted to take the motor back and give me a refund. Thanks to (...) (20 years ago, 12-Dec-06, to lugnet.robotics)
 
  Re: NXT Firmware source code
 
(...) I am curious; have you ever had a situation where bad firmware locked up the NXT? And if so, what was the process to restore it to working order? (I don't have a bricked brick, I'm just asking for future reference.) (20 years ago, 12-Dec-06, to lugnet.robotics.nxt)
 
  RE: NXT Firmware source code
 
(...) I've downloaded firmware to NXT 100s of times with no apparent ill effect. (20 years ago, 12-Dec-06, to lugnet.robotics.nxt)
 
  Re: NXT Firmware source code
 
(...) Flash memories all have a limited number of write cycles before they become unreliable. Usually, the on-chip write controller will "load-balance" the writes so that different memory locations all get used the same number of times, (...) (20 years ago, 12-Dec-06, to lugnet.robotics.nxt)
 
  Re: NXT Firmware source code
 
(...) This is very good news. Thanks for the update. I've been waiting for this for a long time, particularly to have a look at the rather weak graphics capabilities. I've had an expanded font (and a much smaller one) kicking around for a while now. (...) (20 years ago, 12-Dec-06, to lugnet.robotics.nxt)
 
  Re: Locked motor
 
(...) Hi all, Unfortunately, there are very little chance that you may repair your 71427. Most of the motors I have seen with locked shaft have their permanent magnet (made from sintered magnetic powder) partially turned back into powder. That's (...) (20 years ago, 12-Dec-06, to lugnet.robotics)
 
  Re: Locked motor
 
(...) Concerning the motors... a while back I discovered that I had a number of the 71427 style motors that had been removed from ZNAP sets and never used (nor tested). Someone expressed an interest in buying them, so I got out the train power (...) (20 years ago, 12-Dec-06, to lugnet.robotics)
 
  Re: Locked motor
 
(...) After doing some Googling... (URL) the internals of the 43362 motor and some of the 71427. Cheers, Merlin. (20 years ago, 12-Dec-06, to lugnet.robotics)
 
  Re: Locked motor
 
(...) I have not taken my locked motor apart (see below) but if it is a gear that is stripped then, as a last resort, these can be replaced with a custom made one. If you are lucky enough to know someone who is a machinist, or in the local Model (...) (20 years ago, 12-Dec-06, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR