 | | WARNING: +5 supply exposed
|
|
Take a moment to look at your Handy Board. There is a thick trace along the top, right and bottom edge. This is your regulated +5 line. Now look very closely at the outer edge of this trace. It should be completely green (covered with solder mask). (...) (28 years ago, 12-Sep-98, to lugnet.robotics.handyboard)
|
| |
 | | WARNING: +5 supply exposed
|
|
Take a moment to look at your Handy Board. There is a thick trace along the top, right and bottom edge. This is your regulated +5 line. Now look very closely at the outer edge of this trace. It should be completely green (covered with solder mask). (...) (28 years ago, 12-Sep-98, to lugnet.robotics.handyboard)
|
| |
 | | Manual reading
|
|
Hi, Besides the source of manual on Interactive C from the internet, Is there any other sources on the IC software for me to find out more on IC , Eg book ? There are a lot of text book concern the software like C++, java , how about Interactive C . (...) (28 years ago, 12-Sep-98, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Hi,all I am trying to write neural-fuzzy code for avioding of obstacle. I am using handy board. I never wrote a code for fuzzy logic. can anybody suggest me any good site on web for fuzzy logic or any book or any code which he has written. Thanks in (...) (28 years ago, 14-Sep-98, to lugnet.robotics.handyboard)
|
| |
 | | Re:
|
|
(...) There's many ways you can approach obstacle avoiding. There are neural nets, evolutionary code (incl. genetic programming and genetic algorithms), finite state machines, and there's hard-coding it into the program (which, of course is no fun (...) (28 years ago, 14-Sep-98, to lugnet.robotics.handyboard)
|
| |
 | | Handyboard on 9V battery?
|
|
Can it be done? I'm using the Handyboard to control my hexapod robot and weight is a problem. At the moment I have 8 AA batteries connected which are not particularly weight light. I'm not using any of the motor driving functions of the board, just (...) (28 years ago, 14-Sep-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: WARNING: +5 supply exposed
|
|
I got my PCB from Miranda Robotics (mail to colin@prospero.u-net.com for more information) in England, and the trace is fully covered. Apperently, not al HandyBoard PCB's ar exactly the same. Thanks for the tip anyway. Jeroen van der Vegt. (...) (...) (28 years ago, 14-Sep-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Re: <obstacles>
|
|
I don't really know how to explain finite state machines (FSMs) or parse trees...(I'm not in computer science...) but my artificial life class's homepage is still up and the text is available through it in post-script format ((URL) everyone that (...) (28 years ago, 14-Sep-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: <obstacles>
|
|
Ok. If you used 2 motors in m1(right) & m3(left) , and your sensor was at the front (and only one), and in port 15, a short program for running it could be: /*Start of avoid.c */ void main(){ while(1){ /*Puts program in an infinite loop*/ fd(1); (...) (28 years ago, 15-Sep-98, to lugnet.robotics.handyboard)
|
| |
 | | Card readers
|
|
Is there anyone familliar with magnetic card readers, I would like to know where I could get some information on them (communications, etc...) Thanks, Joe Hoffmann E-Mail jhoffman@it.sait.ab.ca (28 years ago, 15-Sep-98, to lugnet.robotics.handyboard)
|