To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *4361 (+10)
  Re: bootstrap mode in assembling the HB
 
yes, RP4 is four isolated resistors, and this being part of the serial line circuit, definitely explains your problem if you are using the common-terminal style. you can just install four 1K resistors if you don't have the correct r-pack handy. fred (...) (28 years ago, 9-Sep-98, to lugnet.robotics.handyboard)
 
  Questions for Fred
 
Fred, or who every can answer this. I have implemented the smooth PWM routines and are very happy with them. I notice now that there is a fix for the analog sensor reading bug. One file that is replaced is the lib_hb.c file, which was also the file (...) (28 years ago, 10-Sep-98, to lugnet.robotics.handyboard)
 
  Questions for Fred
 
I guess I should have learned by now, to investigate more before jumping out and asking. I examined the two versions of the lib_hb.c the difference in the analog is the absence of the following code in the smooth pwm code: int _raw_analog(int port) (...) (28 years ago, 10-Sep-98, to lugnet.robotics.handyboard)
 
  Difference between designer and OEM Polariod kit
 
Hi, What's the difference between the Designer and OEM polaroid kits. Which one do I need to hook up the polaroid sensors to the HB? Thanks (28 years ago, 10-Sep-98, to lugnet.robotics.handyboard)
 
  Ramping up and down.
 
Does anyone have any code using the new smooth PWM motor routines to ramp up and ramp down the speed. I have tried a few things with out much successs. Thanks Bill James | work: 972.480.2306 Product Test Specialist | Pager: 972.598.6201 (...) (28 years ago, 10-Sep-98, to lugnet.robotics.handyboard)
 
  Re: Difference between designer and OEM Polariod kit
 
(...) The OEM kit contains two transducers and two ranging circuit boards for about a hundred bucks or so. The designer kit contains only one each of the above, plus an experimental demonstration board with a digital display and driver circuitry, (...) (28 years ago, 11-Sep-98, to lugnet.robotics.handyboard)
 
  Re: Ramping up and down.
 
(...) Not quite, but I made good use of the PWM to provide automatic, feedback-adjusted motor control for straight-line tracking. It might give you some ideas. My 'bot uses differential steering (it looks like a small wheelchair) and used to cruise (...) (28 years ago, 11-Sep-98, to lugnet.robotics.handyboard)
 
  analog problems
 
I am building my handyboard and have been unable to succesfully execute testanalogs(). testmotors(); and testdigitals(); work but when i testanalogs(); either the board displays the current position of the knob (1-256) and freezes, displays the (...) (28 years ago, 11-Sep-98, to lugnet.robotics.handyboard)
 
  Re: analog problems
 
Dear Sam, It is so strange as you already replace all the chips. The "testanalogs()" is used to test A/D feature and analog port of MC68HC11. It will prompt you "Press START to test knob..." You then press START button and the reading of A/D port (...) (28 years ago, 12-Sep-98, to lugnet.robotics.handyboard)
 
  My problems with digital outputs
 
Dear Mr Fred Martin, My project requires digital outputs and does not need to have motor outputs. I have also read your FAQ and one of them states that by adding a hc374 IC chip in a similar fashoin to the one driving the motor circuits, and (...) (28 years ago, 12-Sep-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR