 | | Re: mindstorms NXT
|
|
(...) You can connect some technic bricks to the sides and have studded bricks very easily. Studless design allows you to access the batteries, display, and buttons much easier. Also technic connection are significantly stronger than the old (...) (21 years ago, 5-Jan-06, to lugnet.robotics, FTX)
|
| |
 | | Re: mindstorms NXT
|
|
(...) Right. You cant always do things mechanically as it would complicate the design and might be too far apart. Also, sometimes a single motor doesnt have enough power, so doubling it up helps.... Ram (21 years ago, 5-Jan-06, to lugnet.robotics)
|
| |
 | | Re: mindstorms NXT
|
|
(...) I will speculate with you here. If I was a betting man, I would bet that they just made 3 of them "motor" ports because of power limitations. I highly doubt they used USB. Of course, you could always plop a usb hub into that port and make your (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
|
| |
 | | Re: mindstorms NXT
|
|
(...) Actually, the RCX outputs 0's and 1's to power the motors as it is right now. It uses Pulse Width Modulation (PWM). Basically for 1/3 power 1/3 of the pulse is 1 and the other 2/3 is 0. For full power, the signal is all 1. This creates a (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
|
| |
 | | Re: mindstorms NXT
|
|
(...) Speculation: I think we're looking at some sort of i2c-like type interface here, where you'll find continuous power on one of the pairs and the other two pairs being used as some sort of high-speed digital bidirectional full-duplex or (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
|
| |
 | | Re: mindstorms NXT
|
|
(...) If these lines are purely digital communication lines, adding additional motors will be easy via a multiplexor attached to one of the RJ11 output. Building the multiplexor (or any custom sensors) may not be as easy though. It looks like you (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
|
| |
 | | Re: Mindstorms NXT & Revalation of the MUP
|
|
(...) Congrats John, Steve and the others for making the grade. ;) Shall we place bets on who the un-named fifth candidate was? Mario? ;) I applied for the NXT test program already. I'm very excited about the NXT capabilities. I tried creating a (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
|
| |
 | | Re: mindstorms NXT
|
|
(...) Or they are far enough apart or in a difficult arrangement so that a mechanical link is impractical. (eg: moving WRT each other.) ROSCO (21 years ago, 5-Jan-06, to lugnet.robotics)
|
| |
 | | Re: mindstorms NXT
|
|
(...) So you parallel motors on the same port to do different things? As opposed to using a single motor mechanically coupled to different things? Is this as a result of a single motor not being powerful enough? Or because the two paralleled motors (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
|
| |
 | | Mindstorms 2.0 and MAC users
|
|
Hello all, I spend a good deal of time answering questions via email, but this one I was unsure of. Could one of my fellow robotics experts be helpful with this question, many thanks! Q: "I HAVE JUST BOUGHT THE MINDSTORM 2.0 (sorry for the shouting (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
|