 | | Re: startup questions RIS 2.0
|
|
In lugnet.robotics, Gyl Midroni wrote: I'd hate to keep asking stupid questions. (...) There's no such thing as a stupid question. Andrew Meyer (21 years ago, 13-Sep-05, to lugnet.robotics)
|
| |
 | | Re: 1.0 brick not responding
|
|
(...) Yes, it flashes. (...) Yes it did work, but it's been in storage for a couple of years. (...) At this point, just download firmware. Once I get the communication issues resolved, I'll do programming. (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx)
|
| |
 | | Re: direct manipulation of bits in RCX registers using NQC
|
|
(...) I agree with Steve that the code samples you posted are probably BrickOS. Now to acheive what you want, it might be a waste of power, but you could always blank off the light itself with a peice of black card or thin black packing plastic. If (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: startup questions RIS 2.0
|
|
Okay - when I got my first serial based RCX tower, I had no issues with Win2k, but with the USB device, it is really a matter of the drivers. If you have got it working with the current drivers, then you will be fine. On the supplied disks, there (...) (21 years ago, 13-Sep-05, to lugnet.robotics)
|
| |
 | | Re: direct manipulation of bits in RCX registers using NQC
|
|
(...) Matt, There are a few ways you can program your RCX. The main choice is if you use the standard firmware, or not. The firmware is pretty much like Windows Operating System. If you use NQC & the standard firmware, you don't need to worry about (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: direct manipulation of bits in RCX registers using NQC
|
|
(...) inside the RCX *directly*, not running programs layered on top of the standard firmware. And if you want to use NQC, you have to work within the limits of the standard firmware (OK, ignoring Dick Swan's firmware, which I've still not been able (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: direct manipulation of bits in RCX registers using NQC
|
|
(...) Hi Brian, Thanks for your response. (...) I'm not sure if I get this, because of C code examples I've seen, which I'll discuss again below. (...) I've tried this already, and as you say, it works, but the sensitivity goes waay down. For a (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: RCX to RCX NQC
|
|
On Mon, September 12, 2005 8:03 pm, Brian Davis wrote: ... (...) ... Somewhere in there, it tells you the RCX will not accept the same command twice in a row. Each command has two op codes that are 8 digits apart. So (I think) for SetWatch you (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx)
|
| |
 | | startup questions RIS 2.0
|
|
Recently picked up RIS 2.0 with the USB tower. I'm new to Mindstrorms, so I looked around the web a bit to try to get an idea of what was going on with it. The first thing that struck me was that everywhere it said that Win2K was not supported. (...) (21 years ago, 13-Sep-05, to lugnet.robotics)
|
| |
 | | Re: direct manipulation of bits in RCX registers using NQC
|
|
(...) Perhaps - but the standard firmware implements a "virtual machine", and so you don't generally have access to physical registers. But... (...) You can configure the input port that the light sensor is connected to as a "passive" sensor (so (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx.nqc)
|