To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *42884 (-10)
  Re: direct manipulation of bits in RCX registers using NQC
 
(...) inside the RCX *directly*, not running programs layered on top of the standard firmware. And if you want to use NQC, you have to work within the limits of the standard firmware (OK, ignoring Dick Swan's firmware, which I've still not been able (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx.nqc)
 
  Re: direct manipulation of bits in RCX registers using NQC
 
(...) Hi Brian, Thanks for your response. (...) I'm not sure if I get this, because of C code examples I've seen, which I'll discuss again below. (...) I've tried this already, and as you say, it works, but the sensitivity goes waay down. For a (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx.nqc)
 
  Re: RCX to RCX NQC
 
On Mon, September 12, 2005 8:03 pm, Brian Davis wrote: ... (...) ... Somewhere in there, it tells you the RCX will not accept the same command twice in a row. Each command has two op codes that are 8 digits apart. So (I think) for SetWatch you (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx)
 
  startup questions RIS 2.0
 
Recently picked up RIS 2.0 with the USB tower. I'm new to Mindstrorms, so I looked around the web a bit to try to get an idea of what was going on with it. The first thing that struck me was that everywhere it said that Win2K was not supported. (...) (21 years ago, 13-Sep-05, to lugnet.robotics)
 
  Re: direct manipulation of bits in RCX registers using NQC
 
(...) Perhaps - but the standard firmware implements a "virtual machine", and so you don't generally have access to physical registers. But... (...) You can configure the input port that the light sensor is connected to as a "passive" sensor (so (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx.nqc)
 
  Re: self-propagating RCX program
 
(...) Agreed. I was hoping for much, much more. Specificly, by this definition, I strongly doubt the claim that this is the "first ever" self-reproduction. Some of the mechanical models from a long time ago were similar in concept, but with a (...) (21 years ago, 13-Sep-05, to lugnet.robotics)
 
  RCX to RCX NQC
 
In a semi-followup to Steve's earlier "remote battery tester"... While the standard firmware provides almost no way to get bytes into the RCX (other than "Message()", one byte at a time), it can certainly export them ("SendSerial"). And it occured (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx)
 
  VEX
 
I can't seem to find a lugnet.robotics.otherbrand group, so I will ask here; Has anyone taken a VEX set for a test drive? I haven't, mainly 'cos of the cost versus what you seem to get for the money. Any comments would be welcome. FUT to somewhere (...) (21 years ago, 13-Sep-05, to lugnet.robotics)
 
  direct manipulation of bits in RCX registers using NQC
 
Hi all, Can anyone tell me if it is possible to use NQC to directly set bits in RCX registers? And if so, how does one do it? I've seen C code examples of this in a few places, but no NQC examples. Specifically, I want to turn on and off the red (...) (21 years ago, 12-Sep-05, to lugnet.robotics.rcx.nqc)
 
  Re: Mana Cat
 
Congratulations Eric! Maybe this is the dawn of those outside of the hobby taking Lego seriously as a tool for creating sculptures and robots. I will admit being disappointed to see such a promising project left, but then I am still heartened to (...) (21 years ago, 12-Sep-05, to lugnet.technic, lugnet.robotics, lugnet.build.mecha)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR