 | | Handy Board for Sale!
|
| To Anyone Interested, I have a nearly brand new complete Handy Board for Sale. I used it one week and unfortunately it does not have the capability to do what I want. It is complete with battery installed, serial/charger board, software for IBM, (...) (28 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | |  | | General use PCB
|
| We have been using the Radio Shack, Archer board #276-162A. Specifications: Dimensions 3 inches x 4 inches, with copper lands on one side. 30 holes by 25 holes with mounting holes at 2.5 inch and 3.5 inch spacing. We have to told that Radio Shack (...) (28 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | |  | | Re: Pull Up Resistor
|
| (...) The sensor connectors on the HB already have pullup resistors on the signal inputs (as I recall they were 47K), so you shouldn't need to add an additional pullup. If you want to make sure, just check the signal connection with a voltmeter to (...) (28 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | |  | | yet another hb for sale
|
| One Handyboard, from Gleason Research, specifically GRHB-PC, with all cables, power supply, software, LCD, battery, charger board, etc. Get it with two Lego 9 volt gearmotors (they cost me $19 each) and my key for IC 3.2. Used for one small project, (...) (28 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | |  | | troubleshooting
|
| I am assembling my handyboard and am at the stage where i have completed the motor and analog circuits. When I test hte analog circuit the LCD screen prints"press START to test knob..." when i press start the board beeps and the screen goes blank. (...) (28 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | |  | | CW TECHNOLOGY
|
| ALL, Do you know if the guy from CW Technology who sells MiniBoard is still doing selling them. I sent him an email, but no reply so far. Thanx. Hachemi (28 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | |  | | mouse encoders
|
| hello, does anyone know how to interface the handyboard with a shaft encoder from a mouse? i am interested in using one out of a microsoft mouse, which uses electrical contacts, instead of an optical sensor. what kind of signal is sent from the (...) (28 years ago, 4-Aug-98, to lugnet.robotics.handyboard)
| | |  | | Re: speed of the board
|
| From: (...) I assume you are going to need to do trig functions as well? I've written software that functions as a 2-D odometer, and uses encoders on the two wheels, and I had to write sin,cos,atan2 functions. How are you getting rotational (...) (28 years ago, 4-Aug-98, to lugnet.robotics.handyboard)
| | |  | | HANDY BD EXPANSION
|
| hi, I have gone thru the Handy board expansion schmetic circuit version 3.0 by Mr.Fred Martin whcih updated on the June 14,1998. I have some doubts : 1) What and where is the the Analog pass-through connector (J4) and Motor power pass-through (...) (28 years ago, 4-Aug-98, to lugnet.robotics.handyboard)
| | |  | | FS: HandyBoard
|
| I have an extra HandyBoard that I assembled and tested. Never used in a project. Includes: Controller Board 2x16 line LCD Nicad Batteries RS-232 Interface/ Charger Board RS-232 Cable Cases for Charger and HB AC Adapter $225 If interested: Mike Davis (...) (28 years ago, 4-Aug-98, to lugnet.robotics.handyboard)
| |