 | | Re: What about Fischertechnik?
|
|
REF: Fischertechnik as building components for robots Greetings, We considered using Fischertechnik for building our robots but unfortunately, they occupy more or less the same volume as LEGO parts and our robots had to be small (first within a 12 (...) (28 years ago, 23-Jul-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Sonar Help!
|
|
Fred, I decided not to use the external battery for now and try and get the sonar working using the directions on the web page. Instead of connecting the power throught the Motor Power header, I have simple connect V+ and GND to TIC3's PWR and Grnd (...) (28 years ago, 24-Jul-98, to lugnet.robotics.handyboard)
|
| |
 | | motor power problems
|
|
Hi, everyone. I recently bought a preassembled handyboard from the Robot Store in Hong Kong, and I'm having trouble with motor power. My robot frame has two motors that can run at 3-4.5V. I was planning to use 5AA Nicads as a power supply for the (...) (28 years ago, 25-Jul-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: motor power problems
|
|
in short, the answer is: "you can't use 3 to 4v motors with the Handy Board." basically, these motors are cheap toy motors that are incredibly noisy from an electrical standpoint, plus they want to draw far more current than the Handy Board's motor (...) (28 years ago, 25-Jul-98, to lugnet.robotics.handyboard)
|
| |
 | | troubleshooting
|
|
I have a problem assembleing my hanyboard. I am at the stage where i am doing the digital input circuit. Before this I successfully loaded pcode_hb.s19 into the handyboard and the interactive C message appeared. However, before i loaded pcode_hb.s19 (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: troubleshooting
|
|
In your message you said: (...) good.... (...) yes, this is normal -- before you load pcode_hb.s19, the LCD is just as you describe. (...) d (...) I'm not clear the problem. if you enable "ignore feedback", does it then download properly? if so, (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
 | | RE: fischertechnik
|
|
First of all, the HandyBoard works fine with fischertechnik. I've been using fischertechnik for a variety of purposes since about 1980. I've also used Lego Technic, although less extensively, for ten years or so. Size/Scale: If you build identically (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
 | | 68hc11F1
|
|
Hello all, Thanks for all the replies that you have send. My board is now working, at 16 mhz with flash and ram. Richard (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
 | | ELMO
|
|
Hello all, From December 1997 until now I've been working on my Master's project. It consisted of a theoretical part and a practical part. In the practical part I made a little mobile robot using a Handy Board. In the next couple of weeks I will be (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR Emmiter and Detector for RW Pro
|
|
Hi ! You get a fantastic collection of datasheets and component specs at www.questlink.com regards..... Rajaraman. -----Original Message----- From: Javaid Iqbal <javaid@student.unsw.edu.au> To: Handy Board <handyboard@media.mit.edu> Date: Sunday, (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|