 | | Re: Smart Motor
|
|
(...) I imagine you could bang them out fairly quickly once you've done a few. But, when I mentioned the US$35 figure, that was $16 for the decoder and ~$17 for the motor (via BrickLink). That still doesn't include any taxes and shipping. So, as a (...) (22 years ago, 9-Sep-04, to lugnet.robotics, FTX)
|
| |
 | | Re: Motorized Switch using Monkey Motor
|
|
In lugnet.trains, Mark Riley wrote: <snip> (...) <snip> Oh My Goodness! I didn't even think of that! I've modified all my switches to have both sides powered, but gettting a 9v wire out to a DCC enabled switch motor--that's extraordinarily (...) (22 years ago, 9-Sep-04, to lugnet.trains, lugnet.robotics)
|
| |
 | | Re: Smart Motor
|
|
Joe Strout writes: > Of course I suppose that power would become a problem if you hung > more than a few motors off one RCX output. Any thoughts on what to > do about that? E.g., would it be possible to rig it so that the > motors draw their power (...) (22 years ago, 9-Sep-04, to lugnet.robotics)
|
| |
 | | Re: Motorized Switch using Monkey Motor
|
|
(...) Yep, that's correct. With LDCC you will be able to configure the power as well as the stroke duration (somewhere around 0.1 to 0.2 seconds). Right now, LACC can control stroke duration, but not power, so I'll be modifying LACC for non-smart (...) (22 years ago, 9-Sep-04, to lugnet.trains, lugnet.robotics, FTX)
|
| |
 | | Re: Motorized Switch using Monkey Motor
|
|
(...) OK, thanks for the reminder! It sounds like maybe if you DCC-ise it, you would want the control program to issue non full power commands then? (...) I wish we could get track connectors and wires in bulk at good prices. (22 years ago, 9-Sep-04, to lugnet.trains, lugnet.robotics, FTX)
|
| |
 | | Re: Motorized Switch using Monkey Motor
|
|
(...) Glad you like them! (...) No, all that is required is a standard unmodified switch. The motor has more than enough torque to throw the switch. In fact, I recommend that you feed a lower voltage to the motor as the motorized switch may(1) (...) (22 years ago, 9-Sep-04, to lugnet.trains, lugnet.robotics, FTX)
|
| |
 | | Re: Motorized Switch using Monkey Motor
|
|
(...) (snip) Thanks for the update! Nice job on the renders for the instructions, by the way... Question: does this require switch modification to de-stiffenize the mechanism? Also I assume that this motor is DCC-able using the technique you (...) (22 years ago, 9-Sep-04, to lugnet.trains, lugnet.robotics, FTX)
|
| |
 | | Re: Lego Compatible (was Re: JCX and Legos...)
|
|
I think I must have sent this off-list? I am of the opinion that LEGO time is theraputic. I _WANT_ it to plug-n-play. I don't mind having to have an 'extra' brick in place, or needing several battery boxes, but I would like it to all work with (...) (22 years ago, 9-Sep-04, to lugnet.robotics)
|
| |
 | | Re: Lego Compatible (was Re: JCX and Legos...)
|
|
(...) In short, you insist upon both electrical and mechanical compatability. An interesting point of view which happens to be quite different from mine; I will have to think about it some. Thanks, -Wayne (22 years ago, 9-Sep-04, to lugnet.robotics)
|
| |
 | | Re: Lego Compatible (was Re: JCX and Legos...)
|
|
(...) There's an Expansion Board for the Handyboard that provides 4 inputs for the LEGO active sensors (light and rotation) on 2 lines besides 6 servo ouputs and other good things. (URL) not too difficult to cut the LEGO cables and attach the (...) (22 years ago, 9-Sep-04, to lugnet.robotics)
|