To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *40459 (-10)
  NQC problem...driving me insane!
 
Hey all, I know I must be doing something very simple wrong here - but I can't for the life of me figure it out. What I'm trying to do: Have a light sensor pointed at a surface. Pass that value off to a variable (the variable then contains the (...) (22 years ago, 4-Jul-04, to lugnet.robotics.rcx.nqc, lugnet.org.ca.rtltoronto)
 
  Re: Repairing small 9v battery box
 
(...) I had a large battery box that was did not work reliably (sometimes yes, sometimes no). The problem was burning at a battery contact. The current does not need to be very high to do that if the contact area is very small. The discolored spots (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
 
  Repairing small 9v battery box
 
I've got one recently off od Bricklink, and it seems not to be working. Yes, new battery, yes, battery works in other small 9v boxes, yes, I made sure it was cool (thermal protection). Any ideas? Any suggestions how to troubleshoot or fix it, (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) Steve, no doubt you' re the best !! ;-) quite simple !! perfect!! the good thing is that it works even when program runs.... Thanks a lot (hey Steve have you the seen the gyro-bob on my site, the simplest mechanical alternative to legway: (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) don't give up. without any programming, the remote will drive the spybot. button 1 & 4 control the right motor, button 3 & 5 control the left motor. It seems messed up, but that's how it is. If the motors go the wrong way, you can switch the (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) front,button 3: right) and it looks too hard for me... do I have gave to give up ? :-) thanks Chris. (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: train control
 
(...) There is a fundamental difference between the RCX and a Lego Train controller - the controller uses smooth power from a 3-pin regulator, with the voltage varied using a chain of resistors. The RCX uses PWM power with approximately 166ms square (...) (22 years ago, 3-Jul-04, to lugnet.robotics.rcx.java)
 
  Re: how to program the spybot remote
 
This is not exactly what you are looking for, but I hope it helps! (URL) think you can use the same process, but you will have to learn what code each button on the remote sends. (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) Hi Steve :-) OK, does it means "spybot" listen remote as it was another spybot ?? using exactly same communication functions ? how can you change remote ID ?? do you have a link where I can find further informations about spy communications?? (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) it's sending (1,2, or 3). All the programming is in the Spybot, where you can change how it responds to different buttons. Steve (22 years ago, 3-Jul-04, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR