To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *40454 (-10)
  Re: how to program the spybot remote
 
(...) front,button 3: right) and it looks too hard for me... do I have gave to give up ? :-) thanks Chris. (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: train control
 
(...) There is a fundamental difference between the RCX and a Lego Train controller - the controller uses smooth power from a 3-pin regulator, with the voltage varied using a chain of resistors. The RCX uses PWM power with approximately 166ms square (...) (22 years ago, 3-Jul-04, to lugnet.robotics.rcx.java)
 
  Re: how to program the spybot remote
 
This is not exactly what you are looking for, but I hope it helps! (URL) think you can use the same process, but you will have to learn what code each button on the remote sends. (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) Hi Steve :-) OK, does it means "spybot" listen remote as it was another spybot ?? using exactly same communication functions ? how can you change remote ID ?? do you have a link where I can find further informations about spy communications?? (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) it's sending (1,2, or 3). All the programming is in the Spybot, where you can change how it responds to different buttons. Steve (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  how to program the spybot remote
 
hi everybody ;-) I use brickCC to program my spybot, do you know how I can program remote' s functions ?? (I talk about the spybot's remote) I' m not a programmer specialist so could you give me few code or a good explanation Thanks to all Chris (...) (22 years ago, 3-Jul-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) Instructions for building a diode-based limit switch can be found at (URL) also has a limit switch adapter, that lets you use standard Lego switch sensors to stop a motor without using any sensor ports. (22 years ago, 1-Jul-04, to lugnet.robotics)
 
  Re: phantom.dll control problem
 
----- Original Message ----- From: "Ayse Gaye Soykok" <asoykok@e-kolay.net> <snip> (...) mfc (...) be (...) CreateFile(USB_TOWER, (...) I was able to make it work using precisely this call ... got the basic working VC++ version from here: (URL) I (...) (22 years ago, 29-Jun-04, to lugnet.robotics.rcx)
 
  Re: phantom.dll control problem
 
(...) Hi, I'd like to say "yes this is the problem, how I' ve forgotten" but firmware is downloaded. Test program works but mine does not. I am using the appropraite commands I am sure. Can it be a problem about the aplication? Test program is VB. (...) (22 years ago, 29-Jun-04, to lugnet.robotics.rcx)
 
  Re: phantom.dll control problem
 
Silly question, but - does your RCX have firmware downloaded to it? Rob "Ayse Gaye Soykok" <asoykok@e-kolay.net> wrote in message news:Hzxw7s.1123@lugnet.com... (...) I am (...) controls, in (...) the rcx (...) program(downloaded with (...) may (...) (22 years ago, 28-Jun-04, to lugnet.robotics.rcx)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR