To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *40389 (-10)
  My new website (with some MOC´s)
 
Hi everyone! I want to anounce my new site dedicated to LEGO! Currently, it have only 3 MOC´s, but I hope to make it bigger with the time... I´m also anouncing my new robotic car - with rack-and-pinion steering and rear suspension. You can see the (...) (22 years ago, 13-Jun-04, to lugnet.technic, lugnet.robotics)
 
  Re: Straight moving with only one rotation sensor
 
I tried to include the LDraw file but I had problems posting. (URL) (22 years ago, 12-Jun-04, to lugnet.robotics.rcx.nqc)
 
  Re: Straight moving with only one rotation sensor
 
I tried to include the LDraw file but I had problems posting. (URL) (22 years ago, 12-Jun-04, to lugnet.robotics.rcx.nqc)
 
  Re: Control Cybermaster from RCX with feedback
 
(...) I think it's theoretically possible to communicate an 8 state signal from the RCX to the Cybermaster's passive sensor port. The passive sensor port measures resistance as well as using a switch - the 3 switches in the cybermaster set have (...) (22 years ago, 11-Jun-04, to lugnet.robotics.cybermaster, lugnet.robotics.rcx)
 
  Re: Favorite robot ?
 
(...) lugnet.. I started building J5 about a year ago. Since then I I built on im my rare freetime (family an my on company are taken my time away..) On BrickShelf I'm posting some pictures from time to time. J5 isn't finished jet. I think, I will (...) (22 years ago, 11-Jun-04, to lugnet.robotics)
 
  Re: Control Cybermaster from RCX with feedback
 
(...) This might be old news, but I just tried it anyway... You can connect an RCX motor port to a CyberMaster sensor port and vice versa and get tri-state info. You can distinguish between the motor floating, off, and one of forward or reverse (...) (22 years ago, 11-Jun-04, to lugnet.robotics.cybermaster, lugnet.robotics.rcx)
 
  Re: Control Cybermaster from RCX with feedback
 
(...) Yes, I also hoped for some ready made NQC library e.g., since I saw someone was working on that once (around 2001 in one of these newsgroups) Morten (22 years ago, 11-Jun-04, to lugnet.robotics.cybermaster, lugnet.robotics.rcx)
 
  Re: Straight moving with only one rotation sensor
 
I did this in the past (since disassembled the bot) and found it to be quite reliable; except on slippery surfaces and carpet. :) The trick that I employed was to gear-up the rotation sensor. This causes the rotation sensor to detect even a slight (...) (22 years ago, 11-Jun-04, to lugnet.robotics.rcx.nqc)
 
  P'titgneugneu the stairs climber, was Re: CC3:Stairs,
 
Here is the (URL) write-up> about the robot I built for CC3:Stairs contest, that happened to win ;o) A bit flimsy, not too pretty, but it did the job! (URL) As the results have not been published here, I inserted the official announcement below. (...) (22 years ago, 10-Jun-04, to lugnet.events, lugnet.robotics, lugnet.technic, lugnet.announce, FTX)
 
  Re: Straight moving with only one rotation sensor
 
Have you come across the adder/subtractor drive? Although it make the gear chain slightly more complex - it may mean you can leave out the sensor entirely. The drive has two inputs (A and B), and two outputs - one being A+B, and the other A-B. So if (...) (22 years ago, 10-Jun-04, to lugnet.robotics.rcx.nqc)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR