To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *39864 (-10)
  Re: Get/SetCommTimeouts
 
"Shashank Date" <sdate@everestkc.net> wrote in message news:Htuzyn.6qG@lugnet.com... (...) parameters. I (...) The "SetCommTimeout" function only applies to "COMx" serial ports. You are trying to use it on a USB port! (23 years ago, 29-Feb-04, to lugnet.robotics.rcx)
 
  control large number of leds (?)
 
hi. i'm working in a project in which i'll need to control the brightness of about 700 leds. i've just begun to research solutions - and i'm not sure the hb is the right microcontroller for the job, but i thought perhaps an hb user on this list (...) (23 years ago, 29-Feb-04, to lugnet.robotics.handyboard)
 
  Get/SetCommTimeouts
 
I am trying to write a C program (using VC++ 6.0) to talk to RCX 2.0 on my Win XP (Home Ed) box. Everything seems to be OK except the get/set of Communication parameters. I cannot understand why. I have attached the minimal C program which does (...) (23 years ago, 29-Feb-04, to lugnet.robotics.rcx)
 
  New LUGNET server hardware details
 
So, we've purchased our cool new servers, from Cambridge, MA vendor "PCs for Everyone". Todd and I and several other friends have gotten systems from them before, and have been extremely pleased -- they know their stuff, including Linux, which is (...) (23 years ago, 28-Feb-04, to lugnet.admin.general, lugnet.admin.finance, lugnet.general, lugnet.lego.direct, lugnet.robotics, lugnet.trains, lugnet.technic, lugnet.space, lugnet.castle, lugnet.org, lugnet.announce) !! 
 
  LUGNET server fund drive a roaring success!
 
Update: Thanks to donations totalling over $4K from more than 150 people around the world, we not only hit our target in four short days days but exceeded it -- by a margin wide and comfortable enough to afford a superb hardware configuration and (...) (23 years ago, 28-Feb-04, to lugnet.admin.finance, lugnet.admin.general, lugnet.general, lugnet.robotics, lugnet.trains, lugnet.technic, lugnet.castle, lugnet.space, lugnet.org, lugnet.announce, FTX) !! 
 
  Respondre el missatge: Use of lnp_addressing_write() in an RCX program.
 
You must send the packet to port 0 of the destination. The dest address is conformed by the address in the upper 4 bits and the port in the lower 4 of the char. So if you put address = 6 you are saying -> host=0 port=6 and you must send to host=6, (...) (23 years ago, 27-Feb-04, to lugnet.robotics.rcx.legos)
 
  Re: Sense and grab robot
 
(...) The light sensor that comes with the main set can easily tell the difference between a white and a black ball. I'm not sure how complex of a robot you are wanting your class to build, however, a small grabber on the front of a rover would be (...) (23 years ago, 26-Feb-04, to lugnet.robotics)
 
  Re: Spurious bad readings from sensors
 
(...) Could it be noise getting into the analog power supply? If you're switching between brake and full power with the motor ports, it seems possible that some spikes could get through to the A/D converter. You might be able to test this by (...) (23 years ago, 25-Feb-04, to lugnet.robotics.rcx.legos)
 
  Re: Sense and grab robot
 
(...) Take a look at Mario and Giulio Ferrari's home pages at (URL) and (URL) progects here may be too complex, but I hope that will help. Aus (23 years ago, 25-Feb-04, to lugnet.robotics)
 
  Re: Spurious bad readings from sensors
 
Hi Mark, Thanks for the help. In Steve's legway code he reads from LIGHT_1 and LIGHT_3 (even if there is no sensor hooked to LIGHT_3). When I was running his code with instrumentation for both sensors, I had nothing hooked to SENSOR_3, and I still (...) (23 years ago, 25-Feb-04, to lugnet.robotics.rcx.legos)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR