To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *39704 (-10)
  RE: Writing a pbForth console
 
Thanks, that's exactly what I needed to know. The only problem was that I wasn't waiting for the flow control characters, everything seems to be working beautifully now. Bob -----Original Message----- From: news-gateway@lugnet.com (...) (23 years ago, 30-Jan-04, to lugnet.robotics)
 
  Receiving messages on PC
 
Hi, I'm sure this issue has come up before, but I can't find an answer to my exact question in the archives: Are there any utilities that can be used (preferably a Windows command line utility) to receive the messages sent by SendMessage()? Or any (...) (23 years ago, 30-Jan-04, to lugnet.robotics.rcx.nqc)
 
  RE: WORDLIST
 
I should help with this tooo, maybe this weekend. Sigh. We just got between 60cm and 90 cm of fresh snow, so snowboarding and shovelling will be the primary activities, unless the roads are closed - which does happen frequently... Ralph (...) (23 years ago, 30-Jan-04, to lugnet.robotics.rcx.pbforth)
 
  RE: IR problems
 
(...) EKEY always waits for input. Use EKEY? to see if anything is available... Looking at the source, I see that there is a possiblity that in the time between checking for a character with EKEY? and actually reading it with EKEY, that an error can (...) (23 years ago, 30-Jan-04, to lugnet.robotics.rcx.pbforth)
 
  RE: Writing a pbForth console
 
I'm not sure what you mean by this. First, are you sending using the old serial tower or the new USB tower? The serial tower required a "warmup" if it's been idle for more than 2 seconds or so. Just send a garbage character (CR is usually OK) and (...) (23 years ago, 30-Jan-04, to lugnet.robotics)
 
  Writing a pbForth console
 
Hi, I am currently attempting to write a program which, when run on my computer, will accept network connections over the internet and act as a proxy between the remote user and my brick, which is running pbForth. I am unable to find, however, any (...) (23 years ago, 30-Jan-04, to lugnet.robotics)
 
  Re: Cannot receive with LNP.
 
(...) I never seen the adressing message work .... Try to search if you have the good adress setup in the lnp_adressing_write function. nanobapt (23 years ago, 30-Jan-04, to lugnet.robotics.rcx.legos)
 
  MacNQC 4.0b1 Announcement
 
Hi All, I've uploaded MacNQC 4.0b1. New features are: * RCX Simulator. * Added a Memory Map Panel. * Updated NQC to 3.0a1. If you would like to test it, it can be found at (URL) comments, or feature requests for the next version can be sent to (...) (23 years ago, 28-Jan-04, to lugnet.robotics.rcx.nqc)
 
  Re: BricxCC release 3.3.7.7
 
(...) Upon further review, it would appear that (at least on my machine and one other that I have heard about) the new release of BricxCC (3.3.7.7) does, in fact, correctly download the brickOS firmware. My previous tests were using an old copy of (...) (23 years ago, 30-Jan-04, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.legos, lugnet.robotics.rcx.nqc, lugnet.robotics.spybotics)
 
  Re: WORDLIST
 
(...) There used to be:-) My code was written for pbforth 1.x which turned to be incompatible with 2.x (I've been out of contact with pbForth for some time and only recently got my RCX back). My fault for not testing it on the current version. Mea (...) (23 years ago, 30-Jan-04, to lugnet.robotics.rcx.pbforth)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR