 | | Re: multiple motors
|
|
(...) Rather well... (...) ...but it was beaten by a simpler but slightly heavier 'bot! And it sometimes committed suicide too :-(( Philo (22 years ago, 27-Nov-03, to lugnet.robotics.rcx)
|
| |
| | Re: Robolab, byte codes and assembler
|
|
"Don Stauffer" <BrainChild@Skyler.com> wrote in message news:Hoz4Gp.1zto@lugnet.com... (...) <<SNIP>> (...) The rotation sensor bad counts cannot be fixed at the byte-code level. The problem is "native" to implementation in the underlying firmware (...) (22 years ago, 27-Nov-03, to lugnet.robotics.rcx.robolab)
|
| |
| | !!!!!!REMOVE!!!!!!!
|
|
Please remove this email address from all you email lists. -----Ursprungligt meddelande----- Från: Alex Jayasundara [mailto:AJayasundara@onfin.com] Skickat: den 24 november 2003 18:25 Till: Ruth; lego-robotics@crynwr.com Ämne: Re: HELP, please! USB (...) (22 years ago, 27-Nov-03, to lugnet.robotics)
|
| |
| | Re: Robolab, byte codes and assembler
|
|
Hello Don, Did you had a look to my analysis of this problem ((URL) But unfortunately I don't think that my modification is "competition-legal"... I agree that sampling can occur at the wrong time, but this should not occur more often at low (...) (22 years ago, 27-Nov-03, to lugnet.robotics.rcx.robolab)
|
| |
| | Re: Robolab, byte codes and assembler
|
|
(...) I've used some of the LabView features, though it seems like they work best when used on constants, rather than variables or containers. My impression, though, is that the non-Robolab-specific LabView features aren't what I'm looking for (...) (22 years ago, 27-Nov-03, to lugnet.robotics.rcx.robolab)
|
| |
| | Re: failure in communicaton between RCX & IR Tower
|
|
(...) fine (...) (all (...) Ya, its a real pain in the arse... Rob (22 years ago, 27-Nov-03, to lugnet.robotics.rcx.robolab)
|
| |
| | Re: Robolab, byte codes and assembler
|
|
(...) Robolab can access LASM code (Lego Assembler) which may allow you to write instructions that fit your needs. The LASM documentation is part of the Mindstorms 2.0 SDK available from (URL) not an assembler programmer so I have no idea if this (...) (22 years ago, 27-Nov-03, to lugnet.robotics.rcx.robolab)
|
| |
| | Re: Robolab, byte codes and assembler
|
|
(...) Two problems: 1. From what I've read about the problem, the speed I ran it at was right in the "sweet spot". 2. BrickOS would not qualify for the competition. I wonder if (hope?) the recent unavailability of rotation sensors at Pitsco is (...) (22 years ago, 26-Nov-03, to lugnet.robotics.rcx.robolab, FTX)
|
| |
| | Updates on addresses of sites under ozBricks
|
|
Hi everybody, Due to few changes under ozBricks server, I wanted to update everybody regarding my sites: 1. The ozBricks links sites new address is: (URL) Links might not work for a while (until the entire changes will be done). Please updates your (...) (22 years ago, 26-Nov-03, to lugnet.general, lugnet.castle, lugnet.cad, lugnet.robotics, lugnet.technic, lugnet.space, lugnet.starwars, lugnet.trains, lugnet.pirates, FTX)
|
| |
| | Re: failure in communicaton between RCX & IR Tower
|
|
Hey, Rob, that's what I was doing last night as well.. but I was installing the w2kpro as my virtual machine (VMWare). However, I ran into some system problem and I have to do this again today. If it works with the w2kpro on your toshiba satellite (...) (22 years ago, 26-Nov-03, to lugnet.robotics.rcx.robolab)
|
