To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3851 (-10)
  Re: Addresses of SPI ports
 
Hi Arthur, The SPI expansion header is shown below: ---...--- Pinouts: 1 Gnd | 2 | 1 | 2 Vcc 5V | 4 | 3 | 3 SS* | 6 | 5 | 4 MISO | 8 | 7 | 5 SCK ---...--- 6 MOSI 7 & 8 Not connected I assume you will be using the Handy Board as a MASTER device not a (...) (28 years ago, 20-May-98, to lugnet.robotics.handyboard)
 
  Re: Addresses of SPI ports
 
Hi The SPI Header is connected to port D of the hc11 as follows: Port D Bit 2 - PD2 - MISO Port D Bit 3 - PD3 - MOSI Port D Bit 4 - PD4 - SCK Port D Bit 5 - PD5 - SS All of those pins can be used for general-purpose I/O signals. To program port D (...) (28 years ago, 20-May-98, to lugnet.robotics.handyboard)
 
  Motors, Part 2
 
Ok, I now realize that I only need one or the other motor driver. Now here is the problem. Nothing happens. I type fd(0); in IC and the motors do noting. I have pin 3 of the Wirz board going to pin 1 of the HB motor driver socket. Pin 7 of the Wirz (...) (28 years ago, 20-May-98, to lugnet.robotics.handyboard)
 
  Re: important update to Handy Board standard libraries.
 
(...) you should download and install the new lib files. fred (...) (28 years ago, 20-May-98, to lugnet.robotics.handyboard)
 
  Re: important update to Handy Board standard libraries.
 
Fred, How does the fix affect IC3.2? Jun Nolasco nolasco@inx.net (...) (28 years ago, 20-May-98, to lugnet.robotics.handyboard)
 
  Re: Motors
 
It's one or the other. (...) (28 years ago, 20-May-98, to lugnet.robotics.handyboard)
 
  Motors
 
Anyone have the Wirez electronics motor driver board? Are you supposed to solder on both the L293Ds and the LMD18200s? Or is it just one or the other? Thanks, Mike ---...--- Mike Reiling macman@inreach.com University of the Pacific Student of (...) (28 years ago, 20-May-98, to lugnet.robotics.handyboard)
 
  important update to Handy Board standard libraries.
 
Hi all, There has been a bug lurking in the Handy Board standard library files since the dawn of time (well, 1996, when the HB got started). The bug can happen when you are using multi-tasking, and more than one IC task is performing analog sensor (...) (28 years ago, 20-May-98, to lugnet.robotics.handyboard)
 
  Addresses of SPI ports
 
Hello. I was wondering if anyone knows all 4 addresses for all 4 ports of SPI header. Thank you (28 years ago, 19-May-98, to lugnet.robotics.handyboard)
 
  Re: Handy Board problem
 
(...) You probably mean the Sharp GP1U5x. That one is modifiable so that it can be read like an analog signal. If anyone can direct me to a company in the Netherlands which sells these parts, I would very much like to know. Thanks. (...) ***...*** * (...) (28 years ago, 19-May-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR