To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *37679 (-10)
  Re: The latest rage in pneumatic computing
 
(...) Yes. I've been pondering this for a while. I had thought of using "long pins with friction" pressed into 1x10 technic beam. It gives you 9 holes. You'd have 8 bits plus parity (I doubt I'd use parity though) (...) Yes. Mark had proposed this (...) (23 years ago, 23-Jun-03, to lugnet.robotics)
 
  Re: Robolab upgrade to 2.5.3 and other things
 
(...) Hallo Bill, I've Robolab 2.5. May you tell me where I can download the Service_Pack to upgrading from 2.5 to 2.5.2 ? Unfortunately the italian Dacta distributor have not. Thank you in advance. Alfio Scaletta from Italy (23 years ago, 22-Jun-03, to lugnet.robotics, lugnet.edu, lugnet.robotics.rcx.robolab, lugnet.robotics.edu)
 
  Re: The latest rage in pneumatic computing
 
(...) Yeah, but that would be the whole idea. Otherwise it would be easy.. just knock out axles where you want a 1 and leave 'em in where you want a zero and let a human being read it. But I was thinking of a situation where the output could be fed (...) (23 years ago, 22-Jun-03, to lugnet.robotics)
 
  Re: The latest rage in pneumatic computing
 
Using the paper tape idea - the input consists of a row of holes and spaces. The spaces are large enough for a piston end to get through, and change some part of the meachine on the other side (to store state). Output could be a piston with a sharp (...) (23 years ago, 22-Jun-03, to lugnet.robotics)
 
  Re: The latest rage in pneumatic computing
 
(...) I thought so too, so I designed one. See elsewhere in this thread. (...) Yeah, I thought so too. (...) This is almost exactly what I was envisioning!!! Cool. Glad to know I'm not the only one psychotic enough to come up with a cockamamy idea. (...) (23 years ago, 22-Jun-03, to lugnet.robotics)
 
  Re: The latest rage in pneumatic computing
 
(...) I wonder if there are savings to be made by building the adder from scratch rather than out of standard XOR/AND/OR gates. (...) The big remaining issue is storage - both RAM and ROM. Whilst you can theoretically build this out of flip-flops - (...) (23 years ago, 22-Jun-03, to lugnet.robotics)
 
  Re: The latest rage in pneumatic computing
 
(...) Okay... I've added arrowheads to each line showing air flow direction. The switches are set up so that the center port is the conventional inlet, and the top and bottom ports the outlets. I say conventional, because I don't always use it that (...) (23 years ago, 22-Jun-03, to lugnet.technic, lugnet.robotics)
 
  Re: The latest rage in pneumatic computing
 
(...) Arrow heads showing which direction you expect the air to flow (not including release) would be helpful also. I've tried to figure it out, but I've not had a lot of luck. (...) (23 years ago, 22-Jun-03, to lugnet.technic, lugnet.robotics)
 
  Re: The latest rage in pneumatic computing
 
(...) Well, I didn't invent the single piston gate. I give credit where credit is due. As I said in a previous post. Your single piston AND gate design was inspirational. I talked myself out of this in the past because I could not figure out how to (...) (23 years ago, 22-Jun-03, to lugnet.technic, lugnet.robotics)
 
  Re: The latest rage in pneumatic computing
 
Wow. Thank you so much for the acknowledgement, Kevin. I am genuinely flattered. I've got a bitmap made of the schematic for my 13 switch full adder. It's strictly representative, and not meant to imply how the switches would be positioned in the (...) (23 years ago, 22-Jun-03, to lugnet.technic, lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR