To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *37624 (-10)
  version of firmware
 
Where can i see the version (1.5 or 2.0) of the firmware that is loaded into an RCX? thanks, Rich ___...___ Do you Yahoo!? SBC Yahoo! DSL - Now only $29.95 per month! (URL) (23 years ago, 16-Jun-03, to lugnet.robotics)
 
  Re: MOC - Small Pneumatic Biped Walker
 
(...) Oh my goodness! That is increadible! Wow, I just can't believe it. That must have been one tough cookie to break! May the Walker Maddness never stop! e (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
 
  RE: EGAD! (pneumatics)
 
(...) That sounds like a coil would have to stay energized, consuming power all the time. When power is removed, the state would be reset. Using a motor to move a mechanical valve control would eliminate that problem, but then feedback would be (...) (23 years ago, 16-Jun-03, to lugnet.robotics)
 
  RE: EGAD! (pneumatics)
 
If I remember right, a 555 can be used as a pulse detector. Obviously, a microcontroller is the better choice, but a 555 based circuit (if possible) would be easier to duplicate by the general population. -----Original Message----- From: Philippe (...) (23 years ago, 16-Jun-03, to lugnet.robotics)
 
  Re: OS X Complier problems solved--now struggling with BrickOS
 
(...) You know, I think there's some cosmic law. Just after hitting the send key, I'll almost always realize my question was stupid. Looking at the errors I was getting, I noticed that it was the utilities that you'd already created. firmdl3 has the (...) (23 years ago, 16-Jun-03, to lugnet.robotics.rcx.legos)
 
  Re: maze solving algorithm
 
(...) Can you post your source code please? Thanks, Jona <http:www.24tooth.com LEGO Robotics Group of Ann Arbor> (23 years ago, 16-Jun-03, to lugnet.robotics)
 
  Re: EGAD! (pneumatics)
 
(...) Yes, the switches would need to remember their last set state. Ideally, this would be done through the use of electric pneumatic switches which, when not receiving any power, simply stay in the last position they were set in. If this isn't (...) (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
 
  Re: EGAD! (pneumatics)
 
(...) IMHO, it would be much simpler and precise to measure directly pulse width instead of voltage, that could be done easily with a small microcontroller... Philo www.philohome.com (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
 
  Re: MOC - Small Pneumatic Biped Walker
 
(...) Hi Paul, I use a electronic schematic style when drawing out my pneumatic circuit designs these days. The combination of a piston that is linke to a pneumatic switch is simply a box, with X and C on the left edge, representing the eXpand and (...) (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
 
  Re: EGAD! (pneumatics)
 
(...) When using LEGO's firmware and NQC the maximum number of power levels you have is 8 (plus off?), so the most you can identiy is 9. This of course presumes that current draw by your compressor's motors doesn't mess with the voltage going into (...) (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR