To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *37334 (-10)
  Re: Scout SDK & USB IR Tower?
 
(...) I think you need to use the USB tower and the light tube. The Scout uses VLL IIRC. -Rob. (24 years ago, 14-May-03, to lugnet.robotics.scout)
 
  Re: Custom Pneumatic Parts
 
(...) They need to be more bulky for starters but I think I know how to make one. It would be a nightmare to build one in 1:20 scale that does not leak too much though (at least for me without proper industrial tools). I won't try to explain how (...) (24 years ago, 14-May-03, to lugnet.technic, lugnet.robotics)
 
  Re: uCOG V - my tiniest weight shifting walker
 
(...) I could't resist sharing this picture: (URL) V is a minifig scale walker! I'd have to take dramamine to prevent motion sickness if I were that minifig! LOL! (...) (24 years ago, 14-May-03, to lugnet.technic, lugnet.robotics)
 
  Re: Custom Pneumatic Parts
 
"Tobbe Arnesson" <StPnAtM@lotek.nu> wrote in message news:HEtrzr.1EBt@lugnet.com... (...) they (...) While some are certainly single acting, double acting versions are available: (URL) are better examples than this kicking around, I found one a (...) (24 years ago, 14-May-03, to lugnet.technic, lugnet.robotics)
 
  Re: COG shifter off topic
 
"Kevin L. Clague" <kevin_clague@yahoo.com> wrote in message news:HEu38p.11v8@lugnet.com... (...) ok thanx kelvin as i said "cog" is good for me i was just curious best regards pixel (24 years ago, 14-May-03, to lugnet.technic, lugnet.cad, lugnet.inst, lugnet.robotics)
 
  Re: OS Stability concerns
 
Actually the software was LEGO Chess, so nothing critical. I had opted to install the abbreviated version, but when I gave that computer to my kids I figured there would be room for the full one, but instead of uninstalling the shorter one, well, (...) (24 years ago, 14-May-03, to lugnet.robotics)
 
  Re: I2C interface
 
Hi, Change the declaration for set_motor to: extern "C" void set_motor(unsigned char mask, unsigned char value); and you should be fine. And, yes, it's H8 asm code. Probably could have written it in C, but I tend to prefer asm for low-level type (...) (24 years ago, 13-May-03, to lugnet.robotics)
 
  RE: COG shifter off topic
 
I presume you realise that COG and centroid are only equivalent for a body of uniform density? Tony -----Original Message----- From: news-gateway@lugnet.com [mailto:news-gateway...net.com]On Behalf Of Kevin L. Clague Sent: Wednesday, 14 May 2003 (...) (24 years ago, 13-May-03, to lugnet.robotics)
 
  Re: I2C interface
 
Thanks for your answer! However, I do have some questions about it.. First of all, I looked at the code you send in your post. looks nice, but to be honest, I don't know anything about assembly ( It is assembly, whats being used in the sub (...) (24 years ago, 13-May-03, to lugnet.robotics)
 
  Scout SDK & USB IR Tower?
 
Hi, I just recently downloaded the Scout SDK. I installed the software, but, I cannot get it to see my Scout. When I open the Scout Tool application an error message says "Please be sure your Scout is turned on and within range, then press init (...) (24 years ago, 13-May-03, to lugnet.robotics.scout)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR