To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3671 (-10)
  IR Transmit ?!? HELP
 
I recently assembled a Handy Board, everything is perfect except for the IR Transmitter. The IR Tx LED does not light. It is not the LED itself because I replaced it. I can't seem to figre out what's wrong. Please help. Thank You Peter Eacmen (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  To Prof. Fred Martin: Neat!
 
Hi, I saw your robot at the Trinity fire fighting contest last Sunday. It was neat, and very animate. I was curious to know if you had figured out why it did what it did during your first run (?). And, what type of sensor were you using on the rear (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
Why does it seem like everyone except me needs a pullup resistor and perhaps a capacitor somewhere to operate the Polaroid? I've never had any problems without any of these components. ??? The first time I connected the sensor, it worked perfectly. (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  tsl1301 or 1401
 
Has anyone tried to use one of the TI tsl1301 or 1401 linear sensors with the HB. I ended up with a few but am having a tough time trying to figure out what the data sheets are trying to tell me. Not real clear (to me). Bruce A. Moore (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Handy board help
 
I am interested in using the Handy Board, but I have a few questions about it first. Please help. :) I noticed the Handy Board supports 4 motors but I am interested in using stepper motors with it. Is this possible? If so what modifications would be (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
Are you using a pullup resistor on the ECHO pin? If not that is your problem. The ECHO output is an open collector driver which requires an 4.7 K pull-up resistor between the output and Vcc. The pull-up is necessary for connecting the module to a (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Help!! Polaroid problem!!!
 
I am trying to use one of the Polaroid 6500 kits from Wirz with my senior design project. It doesn't exactly use a handyboard, but our microcontroller is virtually identical at the lowest level. The problem is when we attach the device to the scope, (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  is IC compatible with the MC68HC11F1
 
hi from France, I already have a handy-board running with a 11A1 chip and I plan to adapt the circuit for a 11F1 chip, with the same memory map. Does someone have any experience about running IC with this chip? Will it work with the pcode_hb.s19 (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Help!!! Polaroid problem!
 
I am trying to use one of the Polaroid 6500 kits from Wirz with my senior design project. It doesn't exactly use a handyboard, but our microcontroller is virtually identical at the lowest level. The problem is when we attach the device to the scope, (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Class functions from C++ to C
 
Hi Kate you could use some precompiler to convert C++ to C. I think that the GNU C++ compilers have such a precompiler. (At least the older ones do.) Tom krasing@iastate.edu schrieb: (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR