 | | Re: Interesting BrickOS Timing Results
|
|
From the second scope screen capture here : (URL) you can see that the analog settling time is about 10 microseconds for the rotation sensor. Philo www.philohome.com (...) (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Interesting BrickOS Timing Results
|
|
(...) I've found that any interrupt on the RCX has a minimum overhead of 101 to 113 states (or about 7 us). This is the time taken by the CPU to recognize and dispatch the interrupt plus the time the ROM routine takes to dispatch the interrupt to (...) (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Interesting BrickOS Timing Results
|
|
Joe, That's definitely an improvement! So, that would be a 250 Hz sample rate for any given sensor. I just tried a modification similar to yours that did all 4 conversions every OCRA/B interrupt (or 1 KHz sample rate) and got: IDLE: 82 2ROT: 77 (...) (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Interesting BrickOS Timing Results
|
|
I did some "real world" tests with this update. I was Astounded at what a difference it makes. The bot I was testing with is a killough platform; which I had tried for hours previously, to get it to follow a line smoothly. I think BrickOS was giving (...) (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Spybotics to RCX message
|
|
The following NQC code will define a routine to send a message to the RCX or Scout: // Sends an RCX PBMessage to RCX or Scout // nMessage = 1 - 255 __nolist void SendRCXMessage (const int nMessage) { asm { 0xe3, &nMessage }; asm { 0x17, 37 }; } I'm (...) (24 years ago, 15-Jan-03, to lugnet.robotics.spybotics)
|
| |
 | | Re: Interesting BrickOS Timing Results
|
|
Mark, I retrieved the latest BrickOS from CVS, made clean and made the cpu test program you listed. I then made two small changes (to see what would happen); first the results, then the changes: IDLE: 89 2ROT: 87 NOAD: 91 (see below) NIRQ: 98 (see (...) (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Land mine robot
|
|
(...) Or make your own. "Passive" sensors have a 5V constant current, and the raw value is the resistance, scaled so infinite resistance is 1023. "Active" sensors can draw more power, but I don't know anything about them. (24 years ago, 15-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Interesting BrickOS Timing Results
|
|
(...) The delay was added a long time ago after a bit of discussion on this newsgroup/list. A search through old newsgroup posts will turn up a brief series of three posts with subject "Rom sensor read routine" from Apr/May 1999. The explanation (...) (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Patches on SourceForge? A good/bad way to get changes into brickOS?
|
|
I've just posted (URL) note that there are 4 other patches lingering from as far back as September. Will my patch be looked at because it has been posted there? For info, here is the patch description The last version of binutils that brickOS works (...) (24 years ago, 14-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: I2C device for the RCX
|
|
(...) Lepomux works with a serial protocol (5 bit preamble, 8 bit data, parity) based on a halfbit-clockspeed of 1 kHz. So compared to your I2C-driver it is dead slow (about 33ms/byte = 30 bytes/s). This slow speed has two reasons: - it's possible (...) (24 years ago, 14-Jan-03, to lugnet.robotics)
|