 | | Re: 8475 Motor Tests
|
|
(...) The limitation on the train controller is the wall wart - not the controller itself. There was discussion on this in .trains a while back. Someone built a tranformer box with about 3A output IIRC, and ran several trains with it through an (...) (23 years ago, 9-Jan-03, to lugnet.technic, lugnet.robotics)
|
| |
| | adding power inlet to technic control center
|
|
Before I blindly go in and screw something up because of lack of electronics knowledge, has anybody already tackled this feat? I assume its very easy with a couple of diodes (maybe too easy) to isolate the batteries from the dc input, but I have (...) (23 years ago, 9-Jan-03, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: 8475 Motor Tests
|
|
(...) Holy C......... That's quite high (understatement) for a little LEGO motor. Do you think it's possible that the train controller I used in my test didn't produce enough juice? If that's the case, then the motor has a higher maximum stall (...) (23 years ago, 8-Jan-03, to lugnet.technic, lugnet.robotics)
|
| |
| | Re: Can't run software
|
|
(...) Matthais, When I go to device manager and look for graphic cards there is no listing. I assume that means I don't have a graphics card and that is probably the real basis of my problem. Would that be right? Bill Lane (23 years ago, 8-Jan-03, to lugnet.robotics.spybotics)
|
| |
| | Re: unique Identifer in RCX
|
|
With BrickOS, you could use the host address; which can be changed on the RCX using the view and program buttons. This would limit you to (what?) 8 or 16 RCXs, but that might be a start. // Joe (...) (23 years ago, 8-Jan-03, to lugnet.robotics)
|
| |
| | Re: A Generic Idea
|
|
(...) Ah - OK. But other things in the world (like people) are moving around - it's not always going to be possible to stop, capture a static image - and then reliably navigate based on it. I guess there are niches where such a robot could be (...) (23 years ago, 6-Jan-03, to lugnet.robotics)
|
| |
| | brickOS with BricxCC
|
|
So far I have heard from two people who have successfully used brickOS with BricxCC. I'm interested in whether anyone else has tried using BricxCC to edit/compile/download programs to brickOS. Currently BricxCC requires that the cygwin bin directory (...) (23 years ago, 8-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
| | dll questions
|
|
I'm working on a new release of BricxCC at the moment and I want to better understand the dll utility - specifically the RCX host address and RCX source port options. I think I understand the RCX host address part. Correct me if I'm wrong. Supposing (...) (23 years ago, 8-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
| | RE: 8475 Motor Tests
|
|
I don't have a 5292 motor or I would do this test myself, but it would be possible to get a more direct comparison with the 71427 gear motor. The 1700-RPM output could be geared down to 340 RPM at a gear ratio of 1:5 with 8- and 40-tooth gears. Tony (...) (23 years ago, 8-Jan-03, to lugnet.robotics)
|
| |
| | Re: 8475 Motor Tests
|
|
Hi Thomas, Interesting informations ! I added a link to this thread in my motor comparison page... Philo www.philohome.com (23 years ago, 8-Jan-03, to lugnet.technic, lugnet.robotics)
|
