To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *36074 (-10)
  Re: Can't run software
 
(...) Matthais, When I go to device manager and look for graphic cards there is no listing. I assume that means I don't have a graphics card and that is probably the real basis of my problem. Would that be right? Bill Lane (24 years ago, 8-Jan-03, to lugnet.robotics.spybotics)
 
  Re: unique Identifer in RCX
 
With BrickOS, you could use the host address; which can be changed on the RCX using the view and program buttons. This would limit you to (what?) 8 or 16 RCXs, but that might be a start. // Joe (...) (24 years ago, 8-Jan-03, to lugnet.robotics)
 
  Re: A Generic Idea
 
(...) Ah - OK. But other things in the world (like people) are moving around - it's not always going to be possible to stop, capture a static image - and then reliably navigate based on it. I guess there are niches where such a robot could be (...) (24 years ago, 6-Jan-03, to lugnet.robotics)
 
  brickOS with BricxCC
 
So far I have heard from two people who have successfully used brickOS with BricxCC. I'm interested in whether anyone else has tried using BricxCC to edit/compile/download programs to brickOS. Currently BricxCC requires that the cygwin bin directory (...) (24 years ago, 8-Jan-03, to lugnet.robotics.rcx.legos)
 
  dll questions
 
I'm working on a new release of BricxCC at the moment and I want to better understand the dll utility - specifically the RCX host address and RCX source port options. I think I understand the RCX host address part. Correct me if I'm wrong. Supposing (...) (24 years ago, 8-Jan-03, to lugnet.robotics.rcx.legos)
 
  RE: 8475 Motor Tests
 
I don't have a 5292 motor or I would do this test myself, but it would be possible to get a more direct comparison with the 71427 gear motor. The 1700-RPM output could be geared down to 340 RPM at a gear ratio of 1:5 with 8- and 40-tooth gears. Tony (...) (24 years ago, 8-Jan-03, to lugnet.robotics)
 
  Re: 8475 Motor Tests
 
Hi Thomas, Interesting informations ! I added a link to this thread in my motor comparison page... Philo www.philohome.com (24 years ago, 8-Jan-03, to lugnet.technic, lugnet.robotics)
 
  Re: 8475 Motor Tests
 
Ok, here is an extrapolated result for the short circuit (stalled) test. The current at 9 volts would be 3.6 amps. Since I did not wish to burn up the motor, I checked current readings at both 3 and 6 volts and also measured the DC resistance and (...) (24 years ago, 8-Jan-03, to lugnet.technic, lugnet.robotics)
 
  Re: 8475 Motor Tests
 
(...) Well, check this out: (URL) are a few pictures of the internals of the motor. Quite a few gears! (...) Thanks! TJ (24 years ago, 8-Jan-03, to lugnet.technic, lugnet.robotics)
 
  Re: New RCX sensor: Wire guidance sensor
 
(...) Hi Gus, This is a very impressive project. Thanks for sharing the information. I tested your program with a similar bot just to see your program in action. It performed flawlessly. Bob Fay (24 years ago, 8-Jan-03, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR