 | | servos
|
|
Does anyone know of a good place to get good servos for cheap? Im looking to find 6 servos. thanks alot! phil phil@rent-a-nerd.com www.rent-a-nerd.com (29 years ago, 7-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: servos
|
|
(...) >Im looking to find 6 servos. >thanks alot! >phil >phil@rent-a-nerd.com >www.rent-a-nerd.com >> Phil, Try Tower Hobbies (800) 637-4989 PO BOX 9078, Champaign, IIinois 61826 or Tammies Hobbies (800) 521-5614 12024 SW Canyon Rd., Beaverton OR (...) (29 years ago, 7-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: servos
|
|
Generally, you can get cheaper servos from just about anywhere else than Tower hobbies. The cheapest, but good enough, is Hitec or Cirrus. Tower's Hitec price is not good. Cirrus line(Hobby Shack's line) is cheaper than Hitec. Check (...) (29 years ago, 7-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | Radio communication page
|
|
Thanks for all the (mostly personal) replies to my message. I'll put a page up on the radio communication between the Handy Board and a PC. At the end of the week there will be a first version up and running. It will be accessible from (URL) Sipke (...) (29 years ago, 7-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | battery
|
|
Hey! We've built a play pen for our robot and plan on showing it to everyone who wanders past our display at the Adventures in Super Computing expo on the 22nd. It will be vooming around the box preferably from like 7:30 to 9. My problem is that our (...) (29 years ago, 8-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | SPI ram
|
|
If anyone cares, I have posted my SPI ram card design to the web at (URL) is probably laughable, but I thought it was a good effort for not knowing too much about electronics. Anthony Oren Loeppert *** (URL) * o* * ***> * * * * * | | * * | / * * |/ (...) (29 years ago, 8-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: SPI ram
|
|
Anthony, A easier way to get 8K of EEPROM memory is to use Microchip Technology 25C640 Serial SPI EEPROM Memory. This is a 8 pin DIP device with a built in SPI interface. Cost is about $3 each. I wrote a simple application note to connect to a HB (...) (29 years ago, 8-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | Board Simulator
|
|
Hi All, In the 3.1beta of the Mac version of IC was a board simulator. Is this still supported in the release version for the Mac? Will there be a port to the PC platforms? I find the simulator very helpful in a lot of situations. But since I do my (...) (29 years ago, 8-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | LMD18200
|
|
I just bought the motor driver kit from wirz electronics, and I have finished putting it all together. My question is, do I take the motor drivers off of the HB and put them on the wirz board, or do I leave them on the HB. Question 2: Assuming I (...) (29 years ago, 8-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: LMD18200
|
|
<FontFamily><param>Courier New</param>We've used the Wirz boards with great success here at Washington University. I can answer both of your questions at once, since they're the same thing. YES. Take the drivers off the handyboard, because now the (...) (29 years ago, 8-Apr-98, to lugnet.robotics.handyboard)
|