 | | mailing list
|
|
Please remove me from your list> (29 years ago, 19-Mar-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polaroid sonar connector
|
|
Easy solution. Why waste so much time looking for connectors. Just remove the connector and solder some wires to the board and run those wires to whatever kind of connector you want! -----Original Message----- From: Will Bain <willbain@cs.umt.edu> (...) (29 years ago, 19-Mar-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: H-Bridge
|
|
Hi talking about the H-Bridge.....we are building one here for a 1.5 kW motor with maximal power output of 2.2 kW. This one works with 400V but is also developped for a current of a little more than 10 A (actually 15A). It will be chopped with a (...) (29 years ago, 19-Mar-98, to lugnet.robotics.handyboard)
|
| |
 | | H-Bridge
|
|
Thanks everyone..Ill check those out. Im probably not going to do anything that requires soldering things on the handy board. Unfortunatly, im only borrowing this one. I'll just see if i can borrow a rover with less power hungry motors from the (...) (29 years ago, 19-Mar-98, to lugnet.robotics.handyboard)
|
| |
 | | RE: H-Bridge
|
|
This suggestion isn't even close to what you require, but it may meet the needs of others on the list who are looking for an alternative H-bridge: (URL) can go to 3.5A at 35vdc, and is serially controlled. I don't think it would be hard to build a (...) (29 years ago, 19-Mar-98, to lugnet.robotics.handyboard)
|
| |
 | | defer() ?? [DAT]
|
|
(...) The defer function is used in multithreaded programs when one process doesn't require all the processor cycles that it would ordinarily be allotted. Typically, if you have multiple processes (threads, tasks, whatever) running at the same time, (...) (29 years ago, 19-Mar-98, to lugnet.robotics.handyboard)
|
| |
 | | defer() ??
|
|
Hi ! Does anybody know how the defer() function works ? Also, what are its applications ? Thanks, Sudeshna * %%%...%%% * * * * Sudeshna Banerjee, * * E-mail :sxbanerj@cs.twsu.edu * * @ee.twsu.edu * * * * %%%...%%% * (29 years ago, 19-Mar-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: H-Bridge
|
|
Hello François, HandyBoard group, We had a similar problem when we tried using an R/C model as a mobile base platform for our robot. Searching the net turned up the LMD18200 (3A, 55V H-Bridge) from National Semiconductors, which was suitable for (...) (29 years ago, 18-Mar-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Power
|
|
Richard wrote:<snip, stuff deleted> (...) Ah, that takes me back a bit. I built one in the late 60's from plans in Practical Electronics, used about 40 transistors and mechano bits. Its collision avoidance sensor was based around an OCP71 photo (...) (29 years ago, 18-Mar-98, to lugnet.robotics.handyboard)
|
| |
 | | H-Bridge
|
|
Hello, I am also searching for a preassembled H-Bridge (12 Volt max 10 Amp in continuous mode). If anyone knows a good place to order one, I would be very interested. (We already tried to build the H-Bridge from Chuck Mac Manis but its components (...) (29 years ago, 18-Mar-98, to lugnet.robotics.handyboard)
|