 | | Re: Rover Programming
|
|
(...) OK, why does it need to communicate with the PC? The primary problem is dead reckoning navigation - which is hard on the 'out of the box' RIS because it's very hard to make a robot that can turn a controlled amount or travel a controlled (...) (23 years ago, 24-Jun-02, to lugnet.robotics)
|
| |
| | *** name poll 2nd phase: make your votes ***
|
|
Now is YOUR turn. I've collected the names and present them at the end of this posting. You can vote for ONE ( 1 ) name. Send an eMail to legOS-namepoll@gmx.de with: - the name you vote for - a phrase, choosen by you for example: I vote for: (...) (23 years ago, 24-Jun-02, to lugnet.robotics.rcx.legos)
|
| |
| | legOS new name: a remark
|
|
some of you may have noticed that I didn't include some names. I contacted the LEGO group and asked them about their feelings for a new name. I got the following answer: The new name should not include any of our trademarks, such as: LEGO, (...) (23 years ago, 24-Jun-02, to lugnet.robotics.rcx.legos)
|
| |
| | serial wiring problems
|
|
Hi, I’d like to connect a PAK VI PS/2 coprocessor to the Handyboard using its serial port. I’ve taken a RJ-11 telephone cable and cut it into two pieces, so that I’ve got on one side the leads of the cable without the RJ-11 plug which I want to (...) (23 years ago, 23-Jun-02, to lugnet.robotics.handyboard)
|
| |
| | Re: How do I switch other devices with my RCX.
|
|
(...) AHAHAAHAHAHAHAHAHAHAHAHAHAAA! (my kind of humor) O, man, a day without laughter is a day not lived! For a more serious approach: see response to the other response. Thanks anyway, Chris! :D (23 years ago, 23-Jun-02, to lugnet.robotics)
|
| |
| | Re: How do I switch other devices with my RCX.
|
|
Thank You, Rob, for your quick response. Judging from the two comments I've received, I should have elaborated a bit. I wanted to use a relay to switch the other circuit, but the it wasn't exactly clear to me what specifications the relay should (...) (23 years ago, 23-Jun-02, to lugnet.robotics)
|
| |
| | Re: How do I switch other devices with my RCX.
|
|
Use the output (A, B, or C) to turn on the relay (you can pick those up at Radio Shack or wherever). The relay could be used to switch on a separate power source to power whatever device at whatever power/voltage you deem necessary. -Rob "Da Byte" (...) (23 years ago, 23-Jun-02, to lugnet.robotics)
|
| |
| | Re: How do I switch other devices with my RCX.
|
|
(...) Simply pick up the other device and set it aside, then place the RCX in the location where the other device was. Tada! You have now switched the other device with your RCX! (23 years ago, 23-Jun-02, to lugnet.robotics)
|
| |
| | How do I switch other devices with my RCX.
|
|
Hi! Problem: I want to switch other devices with my RCX. Does anyone know a feasible solution to this problem? Thank You! Da Byte (23 years ago, 22-Jun-02, to lugnet.robotics)
|
| |
| | Spybotics
|
|
I don´t know if you have already seen this but maybe you can get some more info from it. (URL) (23 years ago, 22-Jun-02, to lugnet.robotics)
|
