 | | Re: Three kinds of motors?
|
|
(...) All three work with Mindstorms. * The micromotor is low in power and low in speed - you'd really only want to use it where space is at a premium. The micromotor is just 2x2 studs and two bricks high! * The motor that comes with RIS and RDS is (...) (24 years ago, 17-Dec-01, to lugnet.robotics)
|
| |
| | Three kinds of motors?
|
|
Looking at brickbay for an extra motor for mindstorms i found three different kinds of motor: - Technic motor (not the one it came with RIS) - Technic Mini-motor (RIS one) - Technic Micromotor (?) Can someone explain the differences, and most (...) (24 years ago, 17-Dec-01, to lugnet.robotics)
|
| |
| | Shuting up the RCX
|
|
Hi all. Just a simple question, does anybody know if there is anyway to stop rcx beeping everytime i turn it on or off. It is terribly annoying at 2:00 in the morning :-) Thank Francis (24 years ago, 17-Dec-01, to lugnet.robotics.rcx)
|
| |
| | Re: How to read the touch sensors on the Scout in NQC?
|
|
This program turns on motor A and leaves it running until a touch sensor attached to input 1 is pressed, then it turns off the motor and plays a sound: task main() { On(OUT_A); until(SENSOR_1 == 1); Off(OUT_A); PlaySound(SOUND_UP); } Dave (...) (24 years ago, 16-Dec-01, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
| | Re: How to read the touch sensors on the Scout in NQC?
|
|
Hi Chris, (...) this is a bit crazy, unless your sensor value is a bit pattern. (...) This is sensible, but are you sure it's ok to use equality and not inequalities like SensorValueRaw(1) < 240? (...) but it's equivalent, also in C, where & is (...) (24 years ago, 16-Dec-01, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
| | Re: Home-made One-way valve
|
|
(...) stuff. You say it is not possible to use an air tank in the old style circuit, but would it work with two air tanks, one on the high pressure hose and the other on the vaccuum hose, between the pneumatic "diode" and valve? Jennifer (24 years ago, 16-Dec-01, to lugnet.robotics, lugnet.technic, lugnet.build)
|
| |
| | Re: How to read the touch sensors on the Scout in NQC?
|
|
I've sort of solved my problem, but not in a way which really makes total sense. Both of the below fragments work as expectd: #1 if ((SensorValueRaw(1) & SensorValueRaw(0)) != 255) #2 if ((SensorValueRaw(1) != 255) || (SensorValueRaw(0) != 255)) (...) (24 years ago, 16-Dec-01, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
| | How to read the touch sensors on the Scout in NQC?
|
|
All, I'm feeling pretty stupid right about now. I've read the NQC docs, looked in the newsgroups, books, etc, but I can't seem to figure out how to read the touch sensors on my Scout. I want to implement a bumper checking task but no matter how I (...) (24 years ago, 16-Dec-01, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
| | Re: About SensorValueRaw(SENSOR_3) in Scout
|
|
Zhengrong, I'm sure you figured this out by now, but I just got it last night so here is a task which reads the light sensor and outputs a sound based on the raw reading. task drone() { CalibrateSensor(); while (shut_up==0) { int b = (...) (24 years ago, 16-Dec-01, to lugnet.robotics.scout)
|
| |
| | Re: MIDI to NQC/RIS2.0 translator "Midi2LSC"
|
|
Makino-san, I'm gald you did this because you just saved me the trouble of doing it myself!!! Thanks, Chris Barker (...) (24 years ago, 16-Dec-01, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
|
